Category: IP Based

(Results from 1 to 10)
Isonas RC-03 Readers - Enabling Wiegand Interface Module (WIM)
To enable WIM on an RC03, first ensure it is properly installed by following page 31 of the RC-03 Manual: Download RC-03 Manual Then use ReaderTester Tool (from DBCrystal Software Package) or Re...
Schlage Commercial » Software » Isonas | Schlage Commercial » Readers » IP Based
Does the RC-04 ship with a short pigtail cable?
No, the Isonas RC-04  reader controllers do not ship with a pigtail.Here is the part number to order:CABLE-RC04-25  -   25’ RC-04 Pigtail CableWe do not offer longer pi...
Schlage Commercial » Software » Isonas | Schlage Commercial » Readers » IP Based
Isonas - RC03, RC04, and IP Bridges Not Returning to "Client" Mode after Firmware Update
Occasionally, an Isonas Access Point will not return to Client mode after updating firmware, or attempting to update firmware.  Firmware updates are completed using the Isonas Configuration Too...
Schlage Commercial » Software » Isonas | Schlage Commercial » Readers » IP Based
Isonas Pure Access Cloud - Auto-Unlock w/Badge Schedules and Engage Devices
Schlage Engage devices linked into Pure Access Cloud use a slightly different command structure than previous Isonas-only devices.  Because of this, there will be an error message that occurs whe...
Schlage Commercial » Software » Isonas | Schlage Commercial » Readers » IP Based
Isonas Pure Access Cloud - Adding Placeholder (Dummy) MAC Addresses for Access Points
NOTE: This guide is for Isonas branded hardware only: RC03, RC04, and IP Bridges. It is common practice to plan access control schemes prior to hardware installation. In Pure Access Clou...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Readers » IP Based
Isonas Pure Access Cloud - Replacing an Existing Reader
Note: This guide is only for Isonas-branded devices: RC03, RC04, IP BridgeIf a reader/access point must be replaced with new hardware in Pure Access.First:1) Go to Access Points page.2) Click on the t...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Readers » IP Based
What is the difference between a PIM400-1501 and a PIM400-485?
The PIM400-1501 has the addition of a Mercury board which allows an IP addressable solution for networking up to 16 AD series devices.  ...
Schlage Commercial » Electronic Locks » Networked » AD 300 Series | Schlage Commercial » Electronic Locks » Networked » AD 400 Series | Schlage Commercial » Readers » IP Based
Schlage RC11, RC15, RCK15 - What Network Ports are Used?
The ports used in a Schlage RC are not fixed and are determined by what URLs are entered into the RC's configuration, so they can be any available port. Isonas Pure Access with Schlage RC takes c...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Readers » IP Based
Schlage RC11, RC15, RCK15 - Reader Not Populating in Isonas Pure Access Cloud
If a Schlage RC has been properly commissioned into the Isonas-created Engage site, and shows as a device in the Engage Mobile App, then it will start trying to communicate with Isonas Pure Access C...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Readers » IP Based
Isonas Pure Access Cloud - Deleting Schlage RC11, RC15, RCK15 from a Tenant and Engage Site?
In order to properly delete a Schlage RC that is linked to Pure Access Cloud: 1) Deactivate the reader in Isonas Pure Access Cloud (PAC). 2) Delete the reader in PAC. 3) Use the Engage M...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Readers » IP Based

Support by product