Category: Exit Devices

(Results from 1 to 10)
How do I program my device?
The programming processes for Allegion devices can be both product and features specific.  Some products programming processes are electronic in nature, others are physical in nature.   ...
Automatic Operators | Biometrics | Credentials | Door Controls | Doors and Frames | Electronic Locks | Exit Devices | Key Systems | Mechanical Accessories | Mechanical Locks | Power Supplies | Readers | Security Management | Software | System Components | Falcon | Glynn-Johnson | Ives | LCN | Schlage | Schlage Electronics | Steelcraft | Von Duprin
What are the amperage and power supply requirements for the Von Duprin Chexit (CX) devices?
Chexit motor driven devices shipped after 8-24-2015:You can use 1 Chexit device with PS902, 3 Chexit devices with PS904, and 4 Chexit devices with PS914 or PS906 power supplies with proper gauge ...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin
What is the best way to test the Von Duprin EL solenoid?
The best way to test the Von Duprin EL solenoid is with an ohm meter. You must test both coils to make sure the solenoid is good. The coil has three wires; green, yellow, and orange. The green wi...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Von Duprin
What is the Falcon lock warranty?
Falcon has a 10 year warranty for its portfolio of locks.  The new warranty is in effect for all locks purchased since November 1st, 2008Electronics/electrified functions will have...
Automatic Operators » Electromechanical » 8200 Series | Automatic Operators » Electromechanical » Benchmark | Exit Devices » Cross Bar » 1990 Series | Exit Devices » Cross Bar » XX Series | Exit Devices » Touch Bar » 1490 Series | Exit Devices » Touch Bar » 1590 Series | Exit Devices » Touch Bar » 1690 Series | Exit Devices » Touch Bar » 1790 Series | Exit Devices » Touch Bar » 17 Series | Exit Devices » Touch Bar » 18 Series | Exit Devices » Touch Bar » 19 Series | Exit Devices » Touch Bar » 24 Series | Exit Devices » Touch Bar » 25 Series | Exit Devices » Touch Bar » 22 Series | Mechanical Locks » Cylindrical » RU Series | Mechanical Locks » Cylindrical » T Series | Mechanical Locks » Cylindrical » W Series | Mechanical Locks » Cylindrical » X Series | Mechanical Locks » Deadbolts » D Series | Mechanical Locks » Mortised » MA-Series | Falcon
How does the Von Duprin 98/99 rim or vertical rod exit device with lever trim convert from L to L-NL function?
To convert the Von Duprin 98/99 Rim or Vertical (Rod or Cable) Exit Device with functional lever (996L-R/V) to act like a rigid lever (996L-NL-R/V) with key over ride follow these steps: Remove the...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin
How far down can an exit device be cut down in the field?
For most exit devices, please refer to the specific device series catalog for minimum door opening width the device can be cut down to fit.Be aware that some device options, frame conditions, and spec...
Exit Devices » Touch Bar » 1490 Series » Falcon | Exit Devices » Touch Bar » 1590 Series » Falcon | Exit Devices » Touch Bar » 1790 Series » Falcon | Exit Devices » Touch Bar » 24 Series » Falcon | Exit Devices » Touch Bar » 25 Series » Falcon | Exit Devices » Touch Bar » 22 Series » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin
How do I change the function of the Von Duprin 7500 mortise lock from Lever ( classroom ) to NL ( night latch )?
To convert the Von Duprin 9975NL(Night Latch or Storeroom) to 9975L (Classroom) exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory): Turn the NL ...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin
What wire gauge and run is recommended for Von Duprin electric latch retraction EL device?
  For Product Shipped Prior to August 2012 using the old (black) potted module: a.       0-100 ft 14 gauge wire b.      0-200 ft 12 ga...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin
What would keep the vertical rod exit devices top latch from being held retracted in the open position?
The following items may cause the exit devices top latch from being held in the retracted position. 1. The top or bottom rods are out of adjustment. 2. The top latch hold back fe...
Exit Devices » Touch Bar » 22 Series » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Von Duprin
How is the QEL calibrated?
Calibration is an internal process of the QEL device when energized the 1st time.  The solenoid will pull and drop 3 times on a standard calibration.  Calibration can be forced by press...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin

Support by product