Category: Electrified System Component Accessories

(Results from 1 to 10)
How is the QEL calibrated?
The QELA motor that has shipped since 2015 is self calibrating. Older versions had a calibration button, and these notes would apply: Calibration is an internal process of the QEL device&nbs...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin
Diode Included with DC Voltage Product
The diode is supplied as optional backfeed protection for many products. There are two ways to tie in these diodes: 1) In series with the + voltage line to load:   Anode to&n...
System Components » Electric Strikes | System Components » Electrified System Component Accessories
Schlage 7764 - Screw Types Included
The 7764 installation kit includes: (4) Phillips sheet metal screws  and (4) wood screws   The kit does not include security screws. ...
System Components » Electrified System Component Accessories
Schlage 442S Cabinet Lock - What Hardware is Included
The 442S Comes packed with: Electrified Latch Body Strike Screw Pack ...
System Components » Electrified System Component Accessories
Can you power an electric strike or maglock from the 9500 Series Senior Swing?
An electric strike or maglock (24 volt only) can be wired to a Senior Swing 2800/9500 series operator using the P10 Lock Interface cable. To power the 24VDC electric strike or maglock ...
Automatic Operators » Electromechanical » Senior Swing » LCN | System Components » Electrified System Component Accessories » Rectifier » Von Duprin
Can 24 volts be run to a 12 volt 6000 series electric strike solenoid?
You can't run 24VDC into the 12VDC electric strike, over voltage such as this will cause the solenoid to heat up and damage the solenoid.  You must change to a 24V solenoid, part number 050240-00....
System Components » Electric Strikes » 6000 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin
How do I identify the voltage on the rotary solenoid for E360/E370 Series lever controls?
The wires are white for both 12 and 24 VDC solenoids for Von Duprin lever controls. The last 3 digits on the solenoid sticker identify the voltage: -032= 12VDC -034= 24VDC ...
System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin
Can the Function of an M996L be changed without connecting to a power supply?
The function of the M996L can be changed from FS to FSE or from FSE to FS with the use of a 9-volt battery.  *Please note, it needs to be a battery with a high charge or it it will be insuffic...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin
Can the M996L be change to fail secure (FSE) before connecting it to a power supply.
A New 9-volt battery can be connected to the leads of the M996 motor to change the function. An older battery may not work. Change the function switch to FSE. Connect the 9V battery to...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin
Where does the EL dogging rod retaining nut go on the dogging rod?
The retaining nut located under the EL adjustment bushing should be located at the very end of the EL dogging rod...
Exit Devices » Touch Bar » 33A/35A Series | Exit Devices » Touch Bar » 98/99 Series | System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin