Category: System Components

(Results from 11 to 20)
Where is common cutout for Von Duprin EPT prep in Ives 224 Continuous Hinge?
Cutout depends on the size of 224 hinge.  See 112HD/224HD-EPT template.  112HD/224HD continuous hinge  Center line of EPT to top of the door  83 inches  30 inches  85 inches  32...
Mechanical Accessories » Hinges & Pivots » Ives | System Components » Power Supplies » EPT Series » Von Duprin
Are the mounting tabs for the EPT-2 and the EPT-10 available?
The mounting tabs are not available for the EPT2 or EPT10....
System Components » Power Supplies » EPT Series » Von Duprin
Does the wire size of an EPT affect the operation of an EL device?
Since most wire transfer devices such as an EPT or electric hinges cannot provide large gauge wires, we take the small gauge wire into account when determining the overall wire size for the device....
Exit Devices » Recessed » 2390 Series » Falcon | Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 1490 Series » Falcon | Exit Devices » Touch Bar » 1590 Series » Falcon | Exit Devices » Touch Bar » 1690 Series » Falcon | Exit Devices » Touch Bar » 1790 Series » Falcon | Exit Devices » Touch Bar » 24 Series » Falcon | Exit Devices » Touch Bar » 25 Series » Falcon | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | System Components » Power Supplies » EPT Series » Von Duprin
Can an EPT be used with Cam Lift Hinges?
An EPT can be used with a Cam Lift Hinge: Maximum hinge lift dimension = 1/2".  The EPT must be installed correctly with the tube at the top on the door side and the tube at bottom on th...
System Components » Power Supplies » EPT Series » Von Duprin
What is the difference between the EPT 2 and the EPT 10?:
The EPT2 has (2) 18 gauge wires and the EPT10 has (10) 24 gauge wires.  Even though they are 18 gauge or 24 gauge wires they are special high stress, high flex, & high current wires specifically u...
System Components » Power Supplies » EPT Series » Von Duprin
No DC output from Power Supply
If a power supply is not outputting DC power, 12 or 24VDC at the Power supply main board lower right terminals ( DC+ DC-), there are several potential causes. ·         Legacy Power Suppl...
System Components » Power Supplies » PS900 Series » Schlage Electronics
What power supply do I use with an L9000 electrified L lock?
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUThese models require 12/24 VDC with a peak current of 0.4 amps.  The following power...
Mechanical Locks » Mortised » L9000 Series | Mechanical Locks » Mortised » L9000 Series » Schlage | Mechanical Locks » Mortised » LV9000-Series | Mechanical Locks » Mortised » LV9000-Series » Schlage | System Components » Power Supplies » PS900 Series » Schlage Electronics
Does the 900-BBK option for the PS900 series recharge the batteries?
Yes, the 900-BBK is a kit that contains the battery backup circuit board and (2) 12V 7 amp/hour batteries which will provide battery back up to the unit when AC fails and will also charge the batter...
System Components » Power Supplies » PS900 Series » Schlage Electronics
What is the warranty on a power supply?
The warranty on the PS900 Schlage Electronics Power Supplies is 12 months from date of manufacture. The warranty is only valid for a true manufacturing defect in the power supply. Any customer damage ...
System Components » Power Supplies » PS900 Series » Schlage Electronics
Are there MSDS sheets for the batteries in the 900-BB?
Attached are the MSDS (material safety data sheet) of the three different manufacturers of batteries for the 900-BB battery backup.   MSDS for 900-BB...
Power Supplies » Standard » PS900 Series » Von Duprin | System Components » Power Supplies » PS900 Series » Schlage Electronics