Category: HP 3000

(Results from 1 to 10)
What does a Warning 80 or 17 mean on a F-Series hand reader?
When you see a Warning 80 or Warning 17 on a HandKey or a HandPunch, it may mean that the lithium battery is low.  The first step is to try a warm boot on the reader to see if that help...
Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics
What does error 64 mean on a HandKey II or Handpunch?
When you see an Error 64 on a HandKey or a HandPunch, it may mean that the lithium battery is low or there is a disconnect with main board.  The first step is to replace the lithiu...
Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics
How do I contact Schlage Biometrics Technical Support?
To contact technical product support for Schlage Biometric Solutions products:Telephone:  877-671-7011, Option 2 (Product Support), Option 8 (Readers, Credentials, Biometrics)Email:  readers...
Biometrics » FingerKey » FingerKey DX Series » Schlage Electronics | Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandKey » ID3D » Schlage Electronics | Biometrics » HandPunch » G Series » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics
How do I upgrade an older biometric F-Series HandKey with a new firmware chip?
The following technical note describes in detail the process for upgrading a biometric F-Series HandKey or a biometric F-Series HandPunch main board with a new firmware chip. Note: A firmware upgrade...
Biometrics » HandKey » HandKey CR » Schlage Electronics | Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandPunch » HP 1000 » Schlage Electronics | Biometrics » HandPunch » HP 2000 » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
What does "Sorry, Can't Add" mean on a hand reader?
The message "Sorry, Can't Add" appears when trying to enroll a user on a hand reader.  There are 2 reasons this message appears:1.  The ID being enrolled already exists in the hand reader.2....
Biometrics » HandKey » HandKey CR » Schlage Electronics | Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandKey » ID3D » Schlage Electronics | Biometrics » HandPunch » HP 1000 » Schlage Electronics | Biometrics » HandPunch » HP 2000 » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
How do you reset a biometric F-Series handreader with a reset switch?
Caution: Resetting/cold booting a biometric handreader resets the handreader to factory default settings and erases the user database. To reset or cold boot a biometric F-Series handreader with a ...
Biometrics » HandKey » HandKey CR » Schlage Electronics | Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandPunch » HP 1000 » Schlage Electronics | Biometrics » HandPunch » HP 2000 » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
What is the standard memory level for a biometric F-series HP-3000-E-XL?
The biometric F-series HandPunch 3000-XL, the HandPunch 3000-E-XL, and the HandPunch 4000 are all "Break Compliant" hand reader models.  Each of these hand readers utilizes an Extended User ...
Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
On a HandPunch when the "Time and Attendance" mode is activated, how do you perform a "Department Code" Function?
On a biometric F-Series hand reader, if the "Time & Attendance" mode is activated:press your ID then #, choose from 1-IN  2-OUT  3-BACK  (press either 1 or 2 or 3); the reader will ...
Biometrics » HandPunch » HP 1000 » Schlage Electronics | Biometrics » HandPunch » HP 2000 » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
If the transaction buffer size for the HP3000 is 5120 records, what is the buffer size on the HP4000?
7680 records.  Because this is a HandPunch unit, once the buffer reaches its limit, the unit will stop accepting punches and will display "Memory Full".  The two ways to resolve this is...
Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics
What happens when you assign all of the password menus on the F and E series readers the same password?
The 5 Command Groups will be combined by assigning them the same password starting with those in password menu 5 and then ending with those in password menu 1.  In this case, the command choices ...
Biometrics » HandKey » HandKey CR » Schlage Electronics | Biometrics » HandKey » HandKey II » Schlage Electronics | Biometrics » HandKey » ID3D » Schlage Electronics | Biometrics » HandPunch » HP 1000 » Schlage Electronics | Biometrics » HandPunch » HP 2000 » Schlage Electronics | Biometrics » HandPunch » HP 3000 » Schlage Electronics | Biometrics » HandPunch » HP 4000 » Schlage Electronics