Category: Mortised

(Results from 51 to 60)
What strike is supplied when HSLR trim is ordered for the L9000 mortise?
10-072 when deadbolt functions are ordered.10-144 (LH/RHR) or 10-145 (RH/LHR) when non deadbolt functions are ordered....
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Mortised | Schlage Commercial
What finish is the cylinder provided with when a lock is ordered in 626AM?
The cylinder is ordered with a lock it will be provided in a 626 finish with no antimicrobial coating.  Rim, Mortise, Core only, and Housing only are NOT offered in AM finish. Whe...
Schlage Commercial » Mechanical Locks » Mortised
Can a Falcon mortise cylinder thumbturn be used on an MA lock?
Not recommend.  If the thumbturn is rotated and left out of position this can cause a bind between the thumb turn cam and the hub in the lock case....
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Mortised | Schlage Commercial » Falcon
What are the dimensions of the latch bolt holes in the 10-072 Strike?
The 10-072 latch & deadbolt holes are: Length 1.455" x Width 0.738" ...
Schlage Commercial » Mechanical Locks » Mortised
How many degrees does it take to unlock the L9040/44 with the thumbturn or coin turn?
The thumbturn on the inside, emergency turn, and coin-turn will take approximately 90 degrees to lock/unlock the mortise case. ...
Schlage Commercial » Mechanical Locks » Mortised
Why would the outside lever activate the RX switch on the electrified L9000 mortise locks?
A couple items may cause this:Springcage may be installed backwards - Springcage must be installed with arrows going in the downward rotation of lever. The L9090 lever hubs will rotate together w...
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series » Schlage » Schlage | Schlage Commercial » Mechanical Locks » Mortised | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series | Schlage Commercial
When did the new Vandlgard LV9000 start shipping from the factory?
The new LV9000 lock cases with the flush handing set screw started shipping on 06/10/2019....
Schlage Commercial » Mechanical Locks » Mortised
When did the L Series change to an new ADA Thumbturn?
Effective December 9, 2019, Schlage L Series mortise locks requiring a thumbturn will ship standard with our new ADA thumbturn. The new ADA thumbturn is slightly smaller than the existing ADA design w...
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Mortised | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series | Schlage Commercial » Mechanical Locks » Mortised » LM9300 Series | Schlage Commercial » Mechanical Locks » Mortised » LMV9300 Series | Schlage Commercial » Mechanical Locks » Mortised » LV9000-Series | Schlage Commercial » Mechanical Locks » Mortised » LM9200 | Schlage Commercial
What was the L Series cylinder retainer part number back from 1992?
Part L283-005 was made up of a plate (L583-036) and two screws (K510-137) and is no longer offered from Schlage, see here for picture. This version was used up until 1994. When L283-005 was ...
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Mortised | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series | Schlage Commercial
Can Buy American Act (BAA) compliance be seen on the order acknowledgement?
Individual products complying with BAA will have a "Y" in the product string of the individual line item.  The "Y" will follow the cylinder suffix code and precede the outside design code. S...
Schlage Commercial » Mechanical Locks | Schlage Commercial » Mechanical Locks » Cylindrical | Schlage Commercial » Mechanical Locks » Mortised

Support by product