Category: Pure Access Cloud

(Results from 81 to 90)
What are the "lock on open" and "lock on close" device settings for a Pure Access Cloud access point?
These settings modify the existing latch interval setting but will only operate when a door position sensor is installed and configured for the access point.- Lock on Open: After an approval or admit,...
Schlage Commercial » Software » Isonas » Pure Access Cloud
In Pure Access Cloud, what is the "Schlage Compatibility Mode" setting in the IP Bridge "Edit Access Point" menu* for?
This enables Schlage Mobile Access Credential compatibility for IP Bridge access points that are equipped with MTB readers.*This setting will only appear for IP Bridge access points in tenants that ar...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » IPBridge
How do Auto-unlock w/Badge events appear in Pure Access Cloud History reports?
For Legacy Isonas devices (RC03, RC04 and IP Bridges), both the start* and the end events are "Badge Unlock" events attributed to "System Admin."*There should be a user attributed approval at the same...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » RC-04 | Schlage Commercial » Software » Isonas » RC-03 | Schlage Commercial » Software » Isonas » IPBridge
Can Pure Access accommodate read in-read out entrances?
Yes, for 12V low current fail secure devices, two reader controllers (RC-04, RC11, RC15) or one 2 door bridge can be used. For higher current, voltage, or fail safe devices, a minimum of one ASM will ...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » RC-04 | Schlage Commercial » Software » Isonas » IPBridge | Schlage Commercial » Software » Isonas » RC Reader Controller
Schlage RC and Pure Access Cloud - Not Connecting after Commissioning
Question:I have commissioned a Schlage RC using Engage Mobile App, within the correct Engage site, and the device is not connecting to, or showing in, Pure Access CloudAnswer:Verify device is commissi...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » RC Reader Controller
Pure Access Cloud - Renaming a Schlage RC (RC11, RC15, RCK15)
When renaming Schlage-branded devices in Pure Access Cloud (PAC), the device name in PAC may not match what is seen as originally named when the devices were added via the Engage Mobile App. If r...
Schlage Commercial » Electronic Locks » ENGAGE Application | Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » RC Reader Controller
How to clear Wi-Fi error code 18 on an NDEB that is linked to an Isonas Pure Access Cloud account?
If receiving error code 18 on an NDEB steps to clear:Deactivate the Device/Access Point in Pure Access Cloud (PAC).Run “Sync Engage Devices” in PAC.Delete the Device/Access Point in PAC.Run “Syn...
Schlage Commercial » Electronic Locks » NDE Series | Schlage Commercial » Software » Isonas | Schlage Commercial » Software » Isonas » Pure Access Cloud
What is the difference between the RC-04-PRX-M and the R-1-MCT-M?
Both the MCT and the PRX models will read 125KHz proximity credentials, but the MCT also reads the13.56MHz smart cards. The MCT model will not read the secure sector data on non-Isonas smart cred...
Schlage Commercial » Software » Isonas » Pure Access Cloud | Schlage Commercial » Software » Isonas » RC-04
The Schlage Reader Controller manual indicates that REX "can be configured active high or active low through configuration settings." How can this be achieved in Pure Access Cloud?
Although the REX will be configurable, field select ability for it is not yet available within Pure Access Cloud.  For proper functionality the use of NC contacts is currently required....
Schlage Commercial » Software » Isonas | Schlage Commercial » Software » Isonas » Pure Access Cloud
With a Pure Access Cloud tenant utilizing AD Connect, is it possible to only sync users and solely manage user groups within the tenant?
No you cannot sync users and solely manage user groups within the tenant.  AD Sync relies on being able to attach users to groups.  You will note that the "Sync" button will not highlig...
Schlage Commercial » Software » Isonas | Schlage Commercial » Software » Isonas » Pure Access Cloud

Support by product