Category: Schlage Commercial

(Results from 31 to 40)
Can I use Primus XP in my SFIC key system?
Primus XP will be available for the Everest SL cylinders.  ...
Schlage Commercial » Key Systems | Schlage Commercial » Key Systems » Cylinder Category | Schlage Commercial » Key Systems » Cylinder Mechanism | Schlage Commercial
Does Engage work with PIV cards
PIV is NOT supported by ENGAGE. The readers on the locks are not compatible with PIV credentials.         ...
Schlage Commercial » Electronic Locks | Schlage Commercial » Electronic Locks » ENGAGE Application | Schlage Commercial » Electronic Locks » NDE Series | Schlage Commercial » Electronic Locks » Gateway | Schlage Commercial | Schlage Commercial » Electronic Locks » LE Series
When did the Schlage motor driven mortise locks launch on the L9090 L9091 L9092 L9093 L9094 L9095?
The new L909x was available to order 10/15/2014, with shipments starting 10/28/2014....
Schlage Commercial » Mechanical Locks » Mortised » L9000 Series » Schlage » Schlage | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series | Schlage Commercial » Mechanical Locks » Mortised » L9000 Series » Schlage | Schlage Commercial
Can I buy a replacement solenoid-driven Chexit module with 0 or 30 second time delay?
No. As of 2016, these special modules are no longer available as replacements for EL Chexit devices. The device will need to be replaced with the new Chexit device, which can then be specifi...
Schlage Commercial » Exit Devices | Schlage Commercial » Exit Devices » Touch Bar | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Schlage Commercial » Von Duprin | Schlage Commercial
What is Zero International?
Schlage Commercial | Schlage Commercial » Zero
What is a the part number for the DPS Magnet and tray on the L909X Mortise locks with Door Position Sensor?
L583-761 DPS Magnet Tray (Used on L909X (non deadbolt models only).L583-760 DPS Magnet (Used on L909X (non deadbolt models only). ...
Schlage Commercial » Mechanical Locks » Mortised » L9000 Series | Schlage Commercial
What is the size of the Hex head arm screw (that holds the rod and shoe in the forearm) for the 1250 or 1450 regular arm closer?
The hex head would require the use of a 10 mm wrench or you can use an adjustable wrench (crescent wrench) as noted in instruction sheet.This hex head arm screw is not an orderable item....
Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Surface Mounted | Schlage Commercial » LCN | Schlage Commercial
Is the LCN 4050A and 4050AT metal covers handed?
Both the 4050A and 4050AT metal covers are Non-handed.   Each metal cover have two cutouts for the spindle and there is an insert used to cover the unused hole. ...
Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Surface Mounted | Schlage Commercial
Can the handing be changed on the LM9200?
The handing on the LM9200 can be changed in the field. Please follow the handing instructions as found in steps 2 and 3 of the LM9200 instruction sheet. Information on the LM9200 lever desig...
Schlage Commercial » Mechanical Locks » Mortised » LM9200 | Schlage Commercial
Is LM9200 available less top latch?
The LM9200 is not available to be ordered less top latch, nor can the LM9200 series be used less top latch. ...
Schlage Commercial » Mechanical Locks » Mortised » LM9200 | Schlage Commercial

Support by product