Category: Schlage

(Results from 11 to 20)
What is the Multi Point LM9300 Series?
MultiPoint locks are three-point locking systems that secure the door at three points – top, bottom, and traditional center latch location. Operating just like traditional locks, MultiPoint locks ar...
Doors and Frames » Doors » B Series » Steelcraft | Doors and Frames » Doors » H Series » Steelcraft | Doors and Frames » Doors » L-Series » Steelcraft | Doors and Frames » Doors » Paladin PW Series » Steelcraft | Doors and Frames » Frames » F & FN Series » Steelcraft | Mechanical Locks » Mortised » LM9300 Series » Schlage | Mechanical Locks » Mortised » LMV9300 Series » Schlage | Schlage | Steelcraft | Von Duprin
What is the finish warranty on Allegion products?
Finish is not specifically stated as being covered under warranty as it is covered under defects in material and workmanship.  EXCEPTION: There is no finish warranty for Falcon products. The...
Schlage
What is the Buy American Act (BAA)?
BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegion we...
Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Electronic Locks » Offline » CO 200 Series » Schlage Electronics | LCN | Schlage | Steelcraft | Von Duprin
Hardware finish warranty
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechProd...
Falcon | Ives | LCN | Schlage | Schlage Electronics | Von Duprin
What is a Grade 1 Lock?
Grade 1 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 800,000 Certified Cycles ANSI/BHM...
Mechanical Locks » Cylindrical » RU Series » Falcon | Mechanical Locks » Cylindrical » T Series » Falcon | Mechanical Locks » Cylindrical » X Series » Falcon | Mechanical Locks » Cylindrical » D Series » Schlage | Mechanical Locks » Cylindrical » ND Series » Schlage | Mechanical Locks » Deadbolts » D Series » Falcon | Mechanical Locks » Deadbolts » B Series » Schlage | Mechanical Locks » Mortised » MA-Series » Falcon | Mechanical Locks » Mortised » L9000 Series » Schlage | Mechanical Locks » Mortised » LM9300 Series » Schlage | Mechanical Locks » Mortised » LV9000-Series » Schlage | Schlage
Will Schlage locks with a BD suffix accept a best SFIC core?
The Schlage B and BD cylinder suffixes designate less small format interchangeable core (SFIC) cylinder prep for the lock. Any SFIC, 6-pin or 7-pin, can be inserted into the lock and will operat...
Key Systems » Cylinder Mechanism » Schlage | Mechanical Locks » Cylindrical » AL Series » Schlage | Mechanical Locks » Cylindrical » ND Series » Schlage | Mechanical Locks » Deadbolts » B Series » Schlage | Mechanical Locks » Tubular / Interconnected » CS200 Series » Schlage | Mechanical Locks » Mortised » L400 Series » Schlage | Mechanical Locks » Mortised » L9000 Series » Schlage | Mechanical Locks » Mortised » LV9000-Series » Schlage | Mechanical Locks » Portable » CL Series » Schlage | Mechanical Locks » Portable » Padlocks » Schlage | Schlage
What height should a lock or deadbolt be installed?
According to ANSI specifications for cylindrical or mortise locks: The lock strike centerline should be 40 5/16" from the bottom of the frame with the lock in relation to the strike. &nbs...
Schlage
What finish will the strike and latch be if ordered with a split finish?
The door handing determines the finish of the latch and strike. Left reverse and right reverse doors default to outside trim Left and right hand doors default to inside trim If lever and r...
Schlage
When was the ME high residential and 505 finish discontinued?
See letter excerpt below.  Parts are no longer available.Effective June 30, 2000 Schlage Commercial is announcing the obsolescence of the ME-Series and ULTIMA 505 bright brass finish option for a...
Schlage
Does Schlage or Falcon manufacture a stainless steel cylindrical or mortise lock?
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless steel...
Mechanical Locks » Cylindrical » X Series » Falcon | Schlage