Category: LCN

(Results from 31 to 40)
Can you use a Senior Swing controller as a replacement for an obsolete Mid Swing controller?
The Mid Swing was discontinued Sept. of 2009. The Sr. Swing control box has the power boost feature which the Mid Swing control box did not have. If you replace only the Mid Swing control box wi...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » LCN
What is a 62A shoe used for?
The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc....
Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4030 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » LCN
Are LCN Closers Fire Rated?
All LCN closers have UL listings and are in compliance to UL10C, and are Fire Rated for up to 3 hours.With regards to the 3 hour rating, all products in this category are considered 3 hour l...
Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Overhead Concealed | Schlage Commercial » Door Controls » Concealed | Schlage Commercial » Door Controls » Surface Mounted | Schlage Commercial » LCN
What is the replacement for an LCN 1070?
 The P1070 was replaced with the 1261 Rw/PA.The 1260 arm can be used as a replacement arm for the discontinued 1070.The P1070 arm can be used on a replacement 1260 body to maintain the original t...
Schlage Commercial » Door Controls » Surface Mounted » 1070 Series » LCN | Schlage Commercial » LCN
What is the maximum door weight recommended for LCN closers?
The maximum recommended door weight for LCN closers is 225 lbs....
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 2610 Series » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 4810 Series » LCN | Schlage Commercial » Door Controls » Overhead Concealed » 2010 Series » LCN | Schlage Commercial » Door Controls » Overhead Concealed » 2030 Series » LCN | Schlage Commercial » Door Controls » Concealed » 3030 Series » LCN | Schlage Commercial » Door Controls » Concealed » 3130 Series » LCN | Schlage Commercial » Door Controls » Concealed » 5030 Series » LCN | Schlage Commercial » Door Controls » Concealed » 6030 Series » LCN | Schlage Commercial » Door Controls » Fire Life Safety » Fire/Life Safety Series » LCN | Schlage Commercial » Door Controls » High Security » 2210 Series » LCN | Schlage Commercial » Door Controls » High Security » 4210 Series » LCN | Schlage Commercial » Door Controls » High Security » 4510 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4010 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4020 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4030 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4110 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4000 Series » LCN | Schlage Commercial » LCN
Can you use a Senior Swing with a Glynn Johnson overhead stop?
It is not a recommended combination.  See below for explanation. The Senior Swing is not set up like any other closer/operator as it truly has an internal dead stop.   If the Seni...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » Mechanical Accessories » Holders and Stops » 100 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 410 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 450 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 81 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 90 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 70 Series » Glynn-Johnson | Schlage Commercial » Mechanical Accessories » Holders and Stops » 79 Series » Glynn-Johnson | Schlage Commercial » LCN
What would cause a door closer to slam?
There are a few things that can cause a closer to slam. The closer could be adjusted incorrectly. Turn all regulating screws clockwise until they stop. Then open each valve 1 and 1/2 turns. If the...
Schlage Commercial » LCN
What is the delay time adjustment on a Delayed Action closers?
Regular LCN closers have "3" regulating valves for General Speed, Latch Speed, and Backcheck. If the LCN closer has "4" regulating valves, then the closer has the Delayed Action feature. Delay...
Schlage Commercial » Door Controls » High Security » 4210 Series » LCN | Schlage Commercial » Door Controls » High Security » 4510 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4010 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4020 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4110 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » SC60 Series » Falcon | Schlage Commercial » Door Controls » Surface Mounted » SC70 Series » Falcon | Schlage Commercial » Door Controls » Surface Mounted » SC80 Series » Falcon | Schlage Commercial » LCN
What closers replaces the 1370 / 1371, which was commonly called the Quest closer?
The 1370 series closer was discontinued on Oct. 4th, 2008The 1260 closer hole pattern is 9-1/16" x 3/4", which is NOT the same hole pattern as the 1370 closer.The 1260-18QF plate does have the same ho...
Schlage Commercial » Door Controls » Surface Mounted » 1070 Series | Schlage Commercial » Door Controls » Surface Mounted » 1070 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1260 Series | Schlage Commercial » LCN
Where is the manufacture date code on a Sr. Swing Motor Gear Box?
The Manufacturing date code for the motor gearbox is located on a silver or white colored sticker near the LCN product label. The digits after "MP" represent the DAY and YEAR year of manufacture. The ...
Schlage Commercial » Automatic Operators | Schlage Commercial » Automatic Operators » Electromechanical | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Automatic Operator | Schlage Commercial » LCN | Schlage Commercial