Category: LCN

(Results from 81 to 90)
What is the minimum header length for an independent pair Sr. Swing operator?
The minimum length header for a Sr. Swing independent pair operator (2 Control Boxes) is 65" for both the surface mounted 9563 (push, pull, or double egress) and the concealed 2863 with an OP arm, or ...
Schlage Commercial » Automatic Operators | Schlage Commercial » Automatic Operators » Electromechanical | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Automatic Operator | Schlage Commercial » LCN | Schlage Commercial
What is the size of the -425 roller locking screw?
The roller locking screw, part #-425, is a set screw.  The size is a 10-32 x 1/4"     (10-32 UNF 3A x 1/4 soc hd cone pt. set screw). This set screw holds...
Schlage Commercial » LCN
What powder coat best matches US10B for a closer?
The closest powder coat finish by LCN is Dark Bronze (BHMA 695)....
Schlage Commercial » LCN
What special template (ST) is used to get a 4040 closer without a spring, for checking only?
ST-2687 is for a closer that is assembled without a spring.   For any large body closer (4010, 4020, 4110, and 4040 series closers), not the 1460/1460T, 1260, 4030/4030T, 2030, 5030, 6030 30...
Schlage Commercial » Door Controls » Overhead Concealed » 2010 Series » LCN | Schlage Commercial » Door Controls » Overhead Concealed » 2030 Series » LCN | Schlage Commercial » Door Controls » Concealed » 5030 Series » LCN | Schlage Commercial » Door Controls » High Security » 2210 Series » LCN | Schlage Commercial » Door Controls » High Security » 4210 Series » LCN | Schlage Commercial » Door Controls » High Security » 4510 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4010 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4020 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4110 Series » LCN | Schlage Commercial » LCN
How is a custom wiring diagram requested?
Request Form Located Here...
Schlage Commercial » Mechanical Locks » Mortised » L9000 Series » Schlage » Schlage | Schlage Commercial » Mechanical Locks » Mortised » LV9000-Series » Schlage | Schlage Commercial » LCN | Schlage Commercial » Schlage Electronics | Schlage Commercial » Von Duprin | Schlage Commercial » Mechanical Locks » Mortised » LM9200
What LCN closers are available in a tri-pack mounting?
The 4040XP, 1260/1261, 1460/1461, 4030/4031 closers have the tri-pack mounting option when ordered with an Rw/PA or Hw/PA designation....
Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4030 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » LCN
How do I get service on my Astro Swing operator that isn't working properly?
LCN does not does not have or supply any information for the old (obsolete) "High Energy" Dor-O-Matic Sliding doors, Bi-Fold doors or Astro Swing doors. You MUST be AAADM certified to work on, or give...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » LCN
Auto operator is opening before QEL retracts the latch. How do I fix this?
If this is a pair of QEL,  you can connect two QEL to a single ouput on a -2RS Board. If you still have a problem you will have to look at either: a) delaying the AO using options o...
Schlage Commercial » LCN | Schlage Commercial » Von Duprin
What is the old 7910-931 RF receiver frequency that LCN used for its ADA products?
The older frequency was 303.875 MHz, and was for the 7910 Series "Linear" products (sold prior to 2009).  The single channel receiver had a part number of 7910-931.   See here for ...
Schlage Commercial » Door Controls » Automatic Operator » 8310 Series » LCN | Schlage Commercial » LCN
Can a Sr swing be used on a door with camlift hinges
Yes, as long as it is a push side mounted operator and it doesn't take 15 lbs or more of force to open the door.NOTE:  The Sr swing is a low energy operator, which means it has to meet ADA standa...
Schlage Commercial » Automatic Operators | Schlage Commercial » Automatic Operators » Electromechanical | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » Door Controls | Schlage Commercial » Door Controls » Automatic Operator | Schlage Commercial » LCN | Schlage Commercial