Category: Power Supplies

(Results from 31 to 40)
Are the batteries for the PS 914 BBK the same as the ones from the 873 BB?
The battery for the PS873 and PS914 are the same, 7AH sealed Lead Acid  battery....
Power Supplies » Standard » PS900 Series » Von Duprin
Will the Von Duprin PS902 power supply operate the QEL device?
The Von Duprin PS902 power supply will operate the QEL device as long as you also use the 900-2Q board for devices shipped prior to September of 2012.  After July of 2012, the 900-2RS board ...
Power Supplies » Standard » PS900 Series » Von Duprin
Will one PS902 power supply run two Von Duprin exit alarm ALK'S?
 One PS902 power supply will run up to six Von Duprin exit alarm ALK devices. PS902  power supply must be set to 24VDC to operate the exit alarm ALK.  Exit alarm ALK exit devices must be as ...
Power Supplies » Standard » PS900 Series » Von Duprin
Where are the PS914 instructions?
The link to the specific sheet can be found by clicking here:  http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/InstallInstructions/Von_Duprin_PS914_Power_Supply_Installation_Inst...
Power Supplies » Standard » PS900 Series » Von Duprin
Will the PS900-2 RS operate the Von Duprin QEL device?
See below for QEL device requirements: QEL devices shipped prior to 7/23/12 must have the 2Q option board for the communication link between the power supply and the exit device.  ...
Power Supplies » Standard » PS900 Series » Von Duprin
How many Chexit devices can be operated from the PS914 power supply?
Following information determine number of the Chexit devices that were shipped prior to 8-24-2015 from the factory with solenoid driven can be hooked up to a single Von Duprin PS873 or PS914 powe...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin
What power supply is required to operate the 6000 series electric strike?
Option boards are not required with PS900 series power supplies when using electric strikes. See the list of options below. The PS902 would power up to 5 electric strikes at 24VDC or ...
Power Supplies » Standard » PS900 Series » Von Duprin | System Components » Electric Strikes » 6000 Series » Von Duprin
How to wire 873-4TD to have 1 input trigger 2 EL devices?
To trigger two EL devices with one access input, wire your input into SC & I1, the first two screw terminals, then jump from I1 to I2 terminals....
Power Supplies » Standard » PS900 Series » Von Duprin
What is needed to keep the EL device retracted all day?
To keep the Von Duprin electric latch retraction EL or QELA exit device dogged (retracted) all day, have your access control, Key pad, key switch, fire alarm contact or any other signals to ...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin
How do I wire an EL device to normally hold open the latch and release it during a fire alarm?
Use a normally closed fire alarm as the input to the power supply option board (PS873-2 or PS914-2RS), this will hold the latch retracted.  During a fire alarm, the contact will open, dropping po...
Exit Devices » Touch Bar » 24 Series » Falcon | Exit Devices » Touch Bar » 25 Series » Falcon | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin