Category: Falcon

(Results from 31 to 40)
How long are the rod lengths for the 25-V?
The top and bottom rod itself is 35" long standard....
Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Why will my EL device not release the solenoid?
Try these steps:Disconnect power from the EL device, if the solenoid plunger releases then and issue is with power going into the device.If it still does not release, try to pull the plunger out of th...
Schlage Commercial » Exit Devices » Recessed » 2390 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series » Von Duprin
Can a 25 series EO device work with any 25 series trim?
The devices are not built function specific and the exit only(EO) devices will accept any of the 500 series trims....
Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Can you take a F-25-C and make it into a F-25-C-WDC?
Device replacement would be required....
Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Can the RG-27 be used with the Falcon XX/19/24/25-V?
The Von Duprin RG-27 will cover the surface vertical rods of the Falcon devices....
Schlage Commercial » Exit Devices » Cross Bar » XX Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 17 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 18 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 19 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Will a 25 series device work with the Omni lock trim previously used on an 18 series device?
We have never tested the Omni lock with the 25 Series device....
Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
What is the Falcon cam designation for use on 25 series trims?
For standard (non-IC) cylinders, use the Falcon #4 straight cam For IC cylinders, use the Falcon #5 cam ...
Schlage Commercial » Exit Devices » Touch Bar » 25 Series | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Will the 800 series trims work on 25 series devices?
The 800 trim will not operate properly on the 25 series devices.  The 25 series 500 series trims lift up on the devices center case where the older 800 series trim for the 18/XX device rotate a s...
Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Do we offer a Dummy Touchbar for the 24 and 25 series devices?
The 250DT is a dummy touchbar for both the 24 and 25 devices.  It is a dummy bar with end caps on each end, no center case....
Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon
Will a 510L or 511L trim work for a vertical, mortise, concealed, or rim device when ordering the trim by itself?
The "500" Series trim in general (510L, 511L, 512's, & 513K) will work with all 25 series devices and are not device specific....
Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon

Support by product