Category: Falcon

(Results from 11 to 20)
What causes the top latch of a 1690 to not hold in the retracted position while the door swings?
The top rod is adjusted too short, so when pushpad is pressed it is not operating the top latch enough to get into the hold down position. The top rod would need to be lengthened by turning the la...
Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon
Can an existing 1990 be changed to an EL1490 and use the existing rods?
The EL1490 does not use the same rods as the 1990. However, the EL1690 would use the existing rods which would be the device used to exchange a 1990 device....
Schlage Commercial » Exit Devices » Cross Bar » 1990 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon
Can you change out a 1990 with a 1690 and would this cover the existing holes?
The 1690 device was designed to replace the older 1990 crossbar device & all  holes would be covered or filled in with set screws....
Schlage Commercial » Exit Devices » Cross Bar » 1990 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon
How do you test the potted circuit breaker or potted module on an EL device?
For Potted Modules (black color) shipped before August of 2012, you can test by applying power to the potted circuit breaker to and if good the following voltages will be seen (be careful to...
Schlage Commercial » Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series » Von Duprin
Is there a part number for extension rods for 1690/1990 devices?
From 9' to 10' use part # 4270100197 extension rod kit. ...
Schlage Commercial » Exit Devices » Cross Bar » 1990 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon
What is the power supply needed for the Dor-O-Matic EL devices?
PS914 with either the 900-2RS option board for powering 1 or 2 devices or the 900-4RL option board for up to 4 devices....
Schlage Commercial » Exit Devices » Recessed » 2390 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon | Schlage Commercial » Power Supplies » Standard » PS900 Series » Von Duprin
Why will my EL device not release the solenoid?
Try these steps:Disconnect power from the EL device, if the solenoid plunger releases then and issue is with power going into the device.If it still does not release, try to pull the plunger out of th...
Schlage Commercial » Exit Devices » Recessed » 2390 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series » Von Duprin
Can a 1790 replace a 1690?
This is possible but the 1790 may not go back into the same location on the door as the 1690 device due to the difference in device backsets. The 1790 must maintain the 3/4" backset from the face...
Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon
Is there a conversion kit to add Electronic Dogging (ED) or Electric Latch Retraction (EL) to a 1690 or 1790 in the field?
There is no conversion kit to add EL or ED to an existing 1690 or 1790 series device. All of the components are built into the device, since the device does not have a separate basepla...
Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon
What material is the end cap and the centercase cover on the 1690 and 1790 made from?
Both the end cap and center case cover of the 1690/1790 are an aluminum die cast material....
Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon

Support by product