CO / AD will not lock but proper LED indications are displayed for validated unlock
Check the key operation Rotate counter clock wise or clock wise, 120 degrees rotation should be observed for latch retraction in either direction. If the points of latch retraction are gros...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
How should I update firmware (FW) on an AD300?
Steps to update firmware on an AD300.
A) Keep the VIN/GND or AUX power applied. The AD300 will not function properly on AA battery power.
B) Connect the SUS/HHD to the USB connector and push...
Schlage Commercial » Electronic Locks » Networked » AD 300 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics
Is the AD CO with a 993 chassis compatible with the Von Duprin 33A exit device?
No, the 33A is not compatible with the AD and CO 993 chassis units. The 33A can only be driven in a clockwise direction. This would restrict it to right hand installs only....
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
How can I return the Reader to its original out-of-the-box configuration?
Starting with AD firmware package ADFwPkg 2.16.3 released 02/11/2011 and CO firmware package COFwPkg 1.20.0 released 3/29/2011; when a second FDR is initiated within 10 seconds of completion of the fi...
Schlage Commercial » Electronic Locks » Networked » AD 300 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 250 Series » Schlage Electronics
Why is the AD400 unlocked after I tested it with my SUS/HHD.
Or force a strike input to the PIM400-TD2. Short J8-1 and J8-2 (Door 1), Short J7-1 and J7-2 (Door 2) on the PIM400-TD2...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics
Why I can’t see the firmware package when connected to the lock?
1. Firmware packages are device dependent. AD locks firmware packages prior to 1/8/2012 are of the naming format ADFwPkgX.X.X.ffp and CO locks COFwPkgX.X.X.ffp.  ...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
Can I use a CM latch retractor with the new AD or CO cylindrical lockset?
It is fine to interchange the CM series cylindrical lockset latches, latch retractors or latch extensions with AD and CO series cylindrical locksets.AD and CO part number for the (2 3/4" backset...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics