Why I can’t see the firmware package when connected to the lock?
1. Firmware packages are device dependent. AD locks firmware packages prior to 1/8/2012 are of the naming format ADFwPkgX.X.X.ffp and CO locks COFwPkgX.X.X.ffp. ...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
Can I use a CM latch retractor with the new AD or CO cylindrical lockset?
It is fine to interchange the CM series cylindrical lockset latches, latch retractors or latch extensions with AD and CO series cylindrical locksets.AD and CO part number for the (2 3/4" backset...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
How long should programming new door files into an AD-Series or Co-Series offline locks take?
To improve door programming file speed, upgrade your SUS to version 4.1.0 or higher...
Schlage Commercial » Electronic Locks » Hand Held Devices » HHD » Schlage Electronics | Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
Resetting the AD400 Lock to factory default settings
Level 1 (FDR) Factory Default reset1. Remove the top inside cover.
2. Press and hold Schlage button on the reader wait for (2) beeps and (2) green flashes (appx 10 seconds).
3. Release the Schlage b...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics
Schlage Utility Software (SUS) is not synchronizing door file information when connected to the lock
When synchronizing door files to the HHD ensure that the SUS is not running.Make certain the proper sync folder location is properly configured in the Schlage express softwareVerify cable proper...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CM Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics | Schlage Commercial » Schlage
What current should an AD-Series or CO-Series lockset draw while in its low power "Sleep" mode?
Use a multi-meter in series with the batteries to measure battery current. Be sure your multi-meter can accurately measure very low current, in the micro-amp range.
See the attached Technical Note:...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 100 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 250 Series » Schlage Electronics
How to terminate RS-485 data lines for third party panels
Use or do whatever Panel manufacturer recommends and uses regarding RS-485 wiring and termination. The IR documentation purposely does not address RS-485 wiring and termination issues ...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics
Why can't I order an AD-Series or CO-Series mortise deadbolt with a classroom/storeroom (70) function
* NOTE: the AD300/400 devices simply communicate the change in Deadbolt Position status to the Host software. The software then decides what action should or should not be taken at the device. ...
Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » AD 200 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Offline » CO 200 Series » Schlage Electronics
How do I couple a Hand Held Device to a PIM400
If the PIM400 has already been coupled with a HHD, the Coupling process will be disabled and the PIM400 will no longer go into its Coupling Mode. You must RESET the PIM400 in order to allow (re-en...
Schlage Commercial » Electronic Locks » Hand Held Devices » HHD » Schlage Electronics | Schlage Commercial » Electronic Locks » Networked » AD 300 Series » Schlage Electronics | Schlage Commercial » Electronic Locks » Networked » AD 400 Series » Schlage Electronics