Category: LCN

(Results from 11 to 20)
How do I order a Senior Swing header?
How to Order: The Senior Swing header is ordered by the width of the door(s). The measurement from inside jamb to inside jamb of the frame. If the Senior Swing header is ordered the wrong length...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
Why is my Senior Swing so hard to open manually?
A Senior Swing operator can be hard to open manually if "Power Boost" feature is turned on, and programmed to the Cn (continuous) setting. To make the door easy to open manually, turn the "Power Boo...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
How do you get the digital read out to light up on the Senior Swing Control Box?
There is a total of 4 red buttons on the front of the Senior Swing control box. To turn on the display, press and hold any 2 of the 4 red buttons at the same time for approximately 3-5 seconds. Your...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
Can a 9500 series operator on the push side be used with Cam lift hinges?
The Senior Swing will work with Cam Lift Hinges as a PUSH SIDE MOUNT 9542/9553/9563 only. Maximum 3/4" lift. Maximum 15 pounds force to push door up the Cam Lift Hinge. Cam Lift Hinges WILL NOT w...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
What would cause a Senior Swing to open too far?
The Senior Swing operator is designed to power open the door to 90°. The built in dead stop (in the gearbox) prevents it from opening any further. If the Senior Swing operator is opening to far (past...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » LCN
Can I get a Senior Swing with a reduced opening force gearbox?
The older model Senior Swing came with 2 spring options. The "standard force" spring required 15 lbs of manual  opening force, and reduced force "RF" required 11 lbs of manual opening force.  All...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
Can you use a Senior Swing controller as a replacement for an obsolete Mid Swing controller?
The Mid Swing was discontinued Sept. of 2009. The Sr. Swing control box has the power boost feature which the Mid Swing control box did not have. If you replace only the Mid Swing control box wi...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » LCN
Where does the 8310-877 safety sensor attach to the Senior Swing controller?
The 8310-877 Bodyguard Safety Sensor attaches (plugs in) to the P1 connector on the Senior Swing controller. The 8310-846 (761462-00) wiring harness "included" with the 8310-877 safety sensor is us...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
What parts are needed to change a Senior Swing 9530 to a 9540 operator?
To convert a 9530 to an 9540 you need to purchase the 9540-3077 REG push arm assembly for reveals up to 10” or 9540-3077L long arm for reveals from 10” to 20”.To convert a 95...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN
Can a Senior Swing 2850 or 2860 be used on a Double Egress (DE) door?
The overhead concealed operators (2850/2860) will not work on a Double Egress frame because the doors are not in the same plane. You will have to use the surface mount (9553 / 9563) on Double Egress ...
Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN

Support by product