Category: LCN

(Results from 21 to 30)
How do you slow down the closing speed of the 4600 series operator?
The hydraulic closer underneath the control box has 3 regulating valves (like any 4040 series hydraulic closer). Main Speed - adjust closing speed from 90° open down to 10°. Latch Speed - ad...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
What parts are required to update an older 4630 or 4640 operator from the old on/off switch and/or I/O board to the new version?
If you have an old digital 4630 or 4640 operator with an I/O Board assembly that has two terminal strips, one with terminals 1-12, and the other that has 13-24 and you are in need of replacing the O...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
4600 with EO3, how to troubleshoot and how can you check the clutch and motor on a 4600 operator?
If you get an EO3 on the control box on a 4600 operator.  E03 = Motor / Clutch not plugged in or open coil.  To troubleshoot follow these steps:Verify that the motor is plugged into the cont...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Is there a special template for a 4640 companion closer?
ST-3066 is the Companion Closer for a 4642 operator. It is a 4642 mounting channel and cover, a manual closer, and with no electronics. Order a 4642 x ST-3066. For current pricing or a...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
What special template (ST) is used with a 4640 operator and a deep reveal?
The "Regular Arm" allows for a reveal up to 4-1/2".The "Long Arm" allows for a reveal between 4-1/2"- 8".ST-3088 is a special "Extra Long Rod" used to mount a 4640 operator on an opening wit...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Where does the hold open switch on the 4630 / 4640 wire into on the 1-24 single terminal strip?
The 4600 hold open switch (for the new 1-24 single terminal strip I/O board) wires into terminals 2 and 6 or 4 and 6....
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Does the 4600 Series (4630 4640) operator have a built in relay?
Yes, the 4600 Series operators have a built in ES (electric strike) relay that can be used to unlock a strike, maglock, or EL device before opening the door....
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
How is the 8310-877 wired to the 4600 (4630 4640) operator?
The 8310-877 comes with a 6 wire cable. You have to cut the connectors off both ends and hardwire it to the 4600 operator as follows: The 6 wire cable connections to the 7 pin connector in the 8310-87...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Can a 4640 operator be mounted on a Flush Ceiling application?
4640 Flush Ceiling mounting requires a minimum 1-3/4" Header, and a minimum 3-3/4" Top Rail on the door....
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Can I make a wireless activated 4640 operator work as alternate action?
The 8310-865 RF receiver contacts (N.O. and COM) would connect to terminals 15 & 17 (the alternate action input) on the 4600 operator. The first activation would open the door, the seco...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN | Schlage Commercial » Door Controls » Automatic Operator » 8310 Series » LCN

Support by product