What is the minimum door opening width for mounting the 4640 or 4630 on a double door?
The minimum door opening width (for mounting a pair of 4640 or 4630 operators on a double door) is 72" wide (2 - 36" door leaves). Mounting the 4640 or 4630 on a double door that is less than 72" w...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
What are the values for the diode and capacitor used with the 4600 operator?
For the newer 4600 I/O Board -- Identified by a 1 to 24 pin terminal block:
As of October 2010 the I/O Board assembly was changed and the new 4600 circuit boards have the capacitor, and diode buil...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Which arm is the same as the 4640 regular arm?
The 4640 Regular arm (4640-3077) is the same as:
4040 Long Arm
4820 Regular arm.
The arms listed above are for reveals up to 4 1/2" and have a 8 3/8" long rod and shoe.
4640 Long arm (46...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 4810 Series » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 4820 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN
What causes an E02 Error Code on a 4600 operator?
An error code E02 indicate a short on the 12/24 VDC power supply.
On current I/O Boards with the 1-24 terminal strip:
Verify any wiring on the power output c...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
What are the Rod and Shoe lengths for 4000 and 1000 series closers?
STANDARD ROD AND SHOE: 4020, 4031, 1460, 1520, 1370, 1070, 1260, 4640, 4820 is: 8 3/8” LONG ROD AND SHOE: 4020, 4031, 1460, 1520, 1370, 1070, 1260, 4640, 4820 is: 12 3/8”STANDARD ROD AND SHOE...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 4820 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1070 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4010 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4020 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4030 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » LCN
Can a Cam Lift hinge be used with LCN closers?
Cam Lift hinges can only be used with LCN door closers that have a "Regular" or "Reg hold Open" style arm. Manual Closers:Maximum lift dimension is 3/4".Can not be use (H)EDA, CUSH, or Trac...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN | Schlage Commercial » Automatic Operators » Electromechanical » 8200 Series » Falcon | Schlage Commercial » Automatic Operators » Electromechanical » Benchmark » LCN | Schlage Commercial » Automatic Operators » Electromechanical » Senior Swing » LCN | Schlage Commercial » Automatic Operators » Pneumatics » 4820 Series » LCN | Schlage Commercial » Door Controls » Fire Life Safety » Fire/Life Safety Series » LCN | Schlage Commercial » Door Controls » High Security » 4510 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1070 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 1460 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4010 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4020 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4030 Series » LCN | Schlage Commercial » Door Controls » Surface Mounted » 4040 Series » LCN | Schlage Commercial » LCN
What is the part number for the 4642 cylinder only?
The 4600 cylinder only part numbers are:
4640 Series -- 4642-3971
4630 Series -- 4631-3971
The 4642-3971 is for push side only and the 4631-3971 is for pull side only....
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
What is the maximum reveal for a regular arm 4642 operator?
Max. reveal for a 4642:
4640 Regular arm -- 4.5"
4640 Long arm -- 8"
4640 x ST-3088 ( custom made - extra long rod) -- 8" to 11"
No special mounting instructions required, just standard template...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Why would a 4600 not open a full 90 degrees?
A 4600 (4630/4640) not opening to a full 90 degrees could be caused by a couple things:
The Opening Force could be set too low. Try increasing the opening force adjustment on the controller a 1/4...
Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN
Can I get parts for an old 4610/4620 auto operator?
The 4610/4620 series operators are obsolete. There is no replacement part for any electronic component (motor/clutch, controller, input/output PC boards) for the obsolete 4610/4620 operators.
Es...
Schlage Commercial » Automatic Operators » Electrohydraulic | Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series | Schlage Commercial » Automatic Operators » Electrohydraulic » 4630 Series » LCN | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series | Schlage Commercial » Automatic Operators » Electrohydraulic » 4640 Series » LCN