Category: Von Duprin

(Results from 11 to 20)
How is the QEL calibrated?
Calibration is an internal process of the QEL device when energized the 1st time.  The solenoid will pull and drop 3 times on a standard calibration.  Calibration can be forced by press...
Exit Devices » Recessed » 94/95 Series INPACT » Von Duprin | Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Power Supplies » Standard » PS900 Series » Von Duprin | System Components » Electrified System Component Accessories » Rectifier » Von Duprin | Von Duprin
When are Panic Devices required?
The use of Panic Hardware and/or Fire Exit Hardware is required by the International Building Code (IBC) and NFPA 101 – The Life Safety Code, depending on which code and which edition of the code is...
Von Duprin | Building Code
Hardware finish warranty
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechProd...
Falcon | Ives | LCN | Schlage | Schlage Electronics | Von Duprin
What is the California State Reference Code regarding lever return?
This is in regards to the California State Reference Code, (Formerly Title 19, California State Fire Marshal Standard) stating that all levers with returns comply; levers must return to within 1/2" ...
Mechanical Locks » Cylindrical » B Series » Falcon | Mechanical Locks » Cylindrical » RU Series » Falcon | Mechanical Locks » Cylindrical » T Series » Falcon | Mechanical Locks » Cylindrical » W Series » Falcon | Mechanical Locks » Cylindrical » AL Series » Schlage | Mechanical Locks » Cylindrical » ND Series » Schlage | Mechanical Locks » Tubular / Interconnected » CS200 Series » Schlage | Mechanical Locks » Mortised » MA-Series » Falcon | Mechanical Locks » Mortised » L9000 Series » Schlage | Mechanical Locks » Mortised » LV9000-Series » Schlage | Mechanical Locks » Tubular / Interconnected » H Series » Falcon | Mechanical Locks » Tubular / Interconnected » Y Series » Falcon | Mechanical Locks » Tubular / Interconnected » S200 Series » Schlage | Mechanical Locks » Tubular / Interconnected » S-Series » Schlage | Falcon | Von Duprin
Lawyer or customer requesting to speak to a legal representative of Allegion.
All inquiries from a customer (Voice mail, Email, Call) regarding specific product information because of an incident, lawsuit or lawyer involvement please send information to Tracy Jaques, tracy...
Key Systems » Cylinder Category » Falcon | Ives | LCN | Von Duprin
What power supply is used to operate the Von Duprin E 996 L trim?
The PS861, PS873, or PS902 power supply can be used to operate the Von Duprin E996L trim.The Von Duprin E996L trim required .22 amps at 24VDC....
Power Supplies » Standard » PS900 Series » Von Duprin | Von Duprin
Will Von Duprin supply the 996L, 996L-BE, 996L-NL and 996L-DT trims with an RX switch?
Von duprin will supply the 996L and 996L-BE trims with RX switch. Von Duprin will not supply the 996L-NL and 996L-DT trims with RX switch because the switch monitors the lever movement and the levers...
Von Duprin
Which strike do you use with an XP98/99 device?
The 909 strike is used in single and paired non-fire rated and single fire rated openings.  The 954 strike is used in fire rated paired openings.The 1609 strike cannot be used with Von Duprin XP98/9...
Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Von Duprin
How do you re-hand the 996 L trim?
See attached instruction for re-handing the 996L/E996L trim.     Click Here: Trim Re-Handing   See page 2....
Von Duprin
Does the 360 L trim have NL function?
To change the function from TL to NL on 360L trim, invert the cam on the mortise cylinder.  See attached instruction 360L trim instruction....
Von Duprin