Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
FALCON MANUAL MA LOCKS
”
RELATED FAQS
Question
Answer
What is the part number for the lever return spring for the old M series mortise lock?
Resolution:
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series. Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...:
How do I remove the lever on an M lock?
Resolution:
To remove the M lock trim follow the steps below in reverse. The M lock spanner wrench is 021415. Although this wrench is no longer available from&n...:
Falcon MA lock wire color.
Resolution:
Solenoid: Black (2 wires) RX (monitors both sides) Normally Open: Green (pin 6 when connector included) Common: Orange (pin 5 when connector included) The current version o...:
Are the M and MA locks compatible?
Resolution:
No parts are compatible between the Falcon MA-Series and the obsolete Falcon M-Series.:
MA launch information
Resolution:
The MA was launched 4/1/10 and replaced the Falcon M lock. :
Does Falcon have a breakaway lever trim feature on mortise locks?
Resolution:
The MA lock does not have Vandlgard or a breakaway trim feature, however, the lever spindle on the MA lock will shear if too much force is applied in order to prevent internal lock damage and resis...:
What non IC cam is offered by Schlage to work in a Falcon MA lock?
Resolution:
Price Book 72A List Price $8.10:
Will the Von Duprin 6210 electric strike operate with the MA series locks?
Resolution:
The Von Duprin 6210 electric strike was designed for retrofit applications and will not work with the Falcon MA series lock when strike and lock body are mounted at standard locations (centerline o...:
Will a Schlage L9000 thumbturn work on a Falcon MA lock?
Resolution:
The Schlage 09-509 Rose style thumbturns will work but the spindle sits 90 degrees off from each other (Schlage is square, Falcon is diamond). The result is the throw will end up 10 and 2 o'c...:
How do I remove an X lock from the door?
Resolution:
To disassemble an X lock, remove the inside knob and unscrew the inside collar and rose. The X lock spanner wrench (012172-000-30) can be used to depress the knob catch as well as tighten/loo...:
How do I identify the old Falcon T lock latch from the new T lock latch?
Resolution:
For T locks shipping mid-June 2013, the new latch can be identified by viewing the deadlatch profile. The profile of the deadlatch has changed from a "full moon" to a "half-moon". See figure below....:
What backsets are available on Schlage and Falcon locks?
Resolution:
SCHLAGE locks are available with the following backsets: Lock Series Lock Type ...:
What parts are needed to convert functions on a 8500 mortise lock body?
Resolution:
See Step 3 of the mortise lock reversing instructions(D-4010) which shows function conversions and what part(s) are needed if any are needed.:
How do I order a lock for a non-standard or thick door?
Resolution:
Most locks will have a standard door range they will install on, but occasionally customers will want to use them on thicker doors. In order to do so, the extended door thick...:
How do I change an AD-Series lock to a different AD-Series lock type?
Resolution:
Re-classing is the process by which an AD-Series device is able to change its lock type. The AD-Series has a modular architecture and a major benefit of this type of architecture is that it allows ...:
Where can I find hurricane ratings for Schlage and Falcon?
Resolution:
There are several Schlage and/or Falcon locks that have been tested and approved for this application. For Commercial use the locks have been tested and approved as ...:
Falcon MA Series
Resolution:
Grade 1 mortise lock:
What drains the AA batteries on an AD-Series lock?
Resolution:
Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1) One the four (or eight) AA was inserted reversed and the rese...:
How do you adjust a door closer?
Resolution:
How to: What are the steps to adjust a door closer? Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All cl...:
Is the Falcon T381 a true classroom security function?
Resolution:
T381 Classroom Security Lock is not a "true" classroom security / Intruder lock function. The T381 is classified as a ANSI/BHMA F88 function: Defined as Grade 1, Apartment, Exit or Public Toil...:
How to remove a double cylinder deadbolt?
Resolution:
Schlage and Falcon double cylinder deadbolts have concealed screws to prevent tampering. The two methods used to conceal the thru-bolts are using screw caps or a faceplate. Use the below instructio...:
What does the cylinder suffix BDC mean?
Resolution:
A small format disposable core is used as a SFIC construction core that is for low security applications and can be thrown in the waste bin after use.:
What are the Falcon T lock electrical requirements?
Resolution:
Prior to June 2011 the T lock only supported 24V and the electrical requirements were as follows: 0.185 amp @ 24VDC Wire Gage 22 AWG See wiring diagram here - (Previous 2 wire versi...:
How do you test a Falcon 24 or 25 Series EL solenoid?
Resolution:
The resistance readings for a Falcon 24 or 25 Series EL solenoid should read;Green to Yellow = Pull Coil, should measure between 1 and 2 ohms of resistance. Green to Orange = Hold Coil, s...:
What is the function of a T571?
Resolution:
Outside lever is locked or unlocked by key. When locked by key it can only be unlocked by key. Push-button locks outside lever. Turning inside lever or closing door releases button. Inside lever i...:
What is a mechanical Lock?
Resolution:
A lock is any device which prevents access or use by requiring special knowledge or equipment. Mechanical locks are mechanical devices which secure an opening by keeping a door closed until a rel...:
When was the Falcon M lock discontinued?
Resolution:
The Falcon M series was discontinued 3/31/10 and was replaced by the Falcon MA series.:
What is the part number for the lever return spring for the MA lock?
Resolution:
Lever assemblies part numbers are found in the Pricebook. Note they are handed.:
Is there an ADA thumbturn offered in the MA locks?
Resolution:
Falcon does not offer an "ADA style thumbturn.:
EL Device Troubleshooting Guide
Resolution:
VISIT US.ALLEGION.COM/EL-SUPPORT FOR TROUBLESHOOTING VIDEO, DOWNLOADABLE GUIDE, AND INSTALLATION INSTRUCTIONS(For best viewing, use Chrome or Firefox browser.)ALLEGION EL SOLENOID ELECTRI...:
How does the W571 operate?
Resolution:
W571 Corridor Lock Deadlocking latch bolt. Push Button Locking. Cannot be locked from outside by key. Button on the inside locks outside lever until unlocked by key or by rotating i...:
How do I manually change PIN length on an AD200?
Resolution:
Beginning with Firmware Packages ADFwPkg 2.16.3 and COFwPkg 1.20.0 the PIN length can be manually changed for AD200 and CO200 locks as follows: 1. Press {programming code (default is 97531)} then ...:
Can the low coin cell Nuisance delay be Disabled on a CO200?
Resolution:
The coin cell is ignored when the lock sets are used with Manual Programming ONLY or while in Construction mode.:
CM Lock Manual Programming Disabled
Resolution:
When trying to program a CM lock, it may display an error code with a solid green light and 10 read flashes. This indicates the lock has already been programmed with computer software and manual ...:
Old 1981 Schlage Lock Service manual.
Resolution:
The 81 service manual can be found here.:
How is a CM lock manually programmed?
Resolution:
In order to manually program a CM lock, there must be a keypad on the reader. If there is not keypad on the reader, then the CM lock can't be manually programmed. Refer to the Schlage 1000 user pro...:
Is the MA lock available with the RX feature?
Resolution:
The MA RX features a single switch within the chassis that will monitor both the inside and outside knob/lever. The switch is only available as Normally Open (NO).:
Where can I find AD/CO Series User Guides?
Resolution:
CO250 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_CO-250_User_Guide_English_104208.pdf:
What is the standard Falcon cam?
Resolution:
Cams for other applications may be specified with no additional charge, see pricebook.:
Where are the part manuals for Falcon exits?
Resolution:
Falcon (19. 24, 25, and XX) parts manuals for Exits are downloadable on the :
How do I change the function of the Von Duprin 7500 mortise lock from Lever ( classroom ) to NL ( night latch )?
Resolution:
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory): Turn the NL screw on 7500 mortise lock counter clo...:
How to order a T series lock with a Corbin Russwin full size interchangeable prep.
Resolution:
Specify the J cylinder suffix followed by IC-CR6 or IC-CR7 (6 or 7 pin Corbin core) Example: T581J IC-CR6 This will accommodate an 8000 or 8000-7 Corbin Russwin Full Size core.:
Why can't I get my JD YA6 cylinder to install into an AD-Series lock?
Resolution:
The JD YA6 tailpiece is intentionally designed such that the tailpiece cannot be installed at the same time as the cylinder. Interchangeable cylinders assume that the lever and taipiece is i...:
What causes the error "Device does not support this action - E802" when I'm coupling an AD lock?
Resolution:
In order to properly couple, the interior pushbutton must be held down while tapping the SW1 (tamper switch) three times. This will enable the lock to couple to the HHD.:
How do I program Locknetics CM / CL legacy locks with the Schlage Utility Software (SUS) and Hand Held Device (HHD)?
Resolution:
- With the CIP NOT inserted and the Schlage Utility Software (SUS) running o Enter the Master Programming PIN or Present Loc...:
Explain the ND80 function.
Resolution:
The 80 (Storeroom function) operates as follows: Key retracts latch (entrance by key only):
How do I program my device?
Resolution:
The programming processes for Allegion devices can be both product and features specific. Some products programming processes are electronic in nature, others are physical in nature. &nb...:
How do I change the handing on my 7500 mortise lock?
Resolution:
You can reference the 7500 mortise lock rehanding instructions. Remove the two screws from mortise lock faceplate. Remove the face plate and the collar from the mortise lock then rotate the la...:
How do you adjust for door thickness on an AL lock?
Resolution:
The standard door range for an AL lock is 1 3/8" to 1 7/8". Using the supplied instruction sheet, align the springcage post to desired door thickness by adjusting the outside castle nut. See inst...:
What firmware does my CO-100 lock have?
Resolution:
CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus. :
What cylinder length do you use for escutcheon trim for the L series mortise lock?
Resolution:
Typically for a 1-3/4" door you would use a 1-1/4" cylinder. Use the Table in the Pricebook for a reference:Note: The 30-001 used with Rose trim on double cylinder applications requires a Blo...:
Are parts still available for the old Falcon M locks?
Resolution:
Related solution: What is the part number for the lever return spring for the old M series mortise lock?:
What is the center to center for the Falcon H lock?
Resolution:
The dimension between the center of the deadbolt bore and the knobset bore is 4". See template FH100 attached here for more dimensions.:
Does Schlage make a level 4 bulletproof lock?
Resolution:
Schlage does not test their locks for ballistics or bullet resistance.:
Can I get the T series with a Schlage Full Size Interchangeable core?
Resolution:
The T lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied (including the tailpiece) Example: T581J IC-SC:
Can I get the RU series with a Schlage Full Size Interchangeable core?
Resolution:
The RU lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied. The tailpiece will come with the lock. Example: RU581J IC-SC:
What is the part number for T lock tailpiece used with a conventional cylinder?
Resolution:
Refer to Table 1 for a list of T lock tailpieces for conventional cylinders. Table 2 shows IC tailpieces. Table 1: T lock conventional tailpieces Table 2: T lock IC tailpieces:
What T lock improvements were made in May 2013?
Resolution:
In mid-May 2013 the Falcon T-Series changed the slide and catch spring used in the chassis to improve overall durability.:
What is the RU lock?
Resolution:
The RU series from Falcon is a pre-assembled unit lock designed to retrofit existing unit locks manufactured by Falcon, Corbin Russwin and Yale. It exceeds ANSI Grade 1 specifications and is ...:
What is a Grade 2 Lock?
Resolution:
Grade 2 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 400,000 Certified Cycles ANSI...:
What is an interconnected lock?
Resolution:
Interconnected Locks: a lockset whose trim provides a means of simultaneous retraction of two or more bolts which may also be operated independently Medium duty Commercial, government or multi-...:
What are the MA lock electrical requirements?
Resolution:
For additional details and a wiring diagram see the MA service manual page on electrical requirements here.:
Will the Falcon MA lock fit a 1-3/8" thick door?
Resolution:
The Falcon MA will not fit a 1-3/8" thick door. :
What is the Buy American Act (BAA)?
Resolution:
BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegio...:
How does the MA531 operate?
Resolution:
MA531 (ANSI F20) Apartment Corridor Door Lock Latch bolt operated by knob/lever from either side, except when outside knob/lever is made inoperative by buttons in face. Dead bolt operated b...:
Explain the MA581 function
Resolution:
MA581 operation: Latchbolt operated by key from outside or by operating inside knob/lever. Outside knob/lever is always inoperative. Auxiliary latch deadlocks latchbolt when door is locked.:
Does the Falcon T series have an RX option available?
Resolution:
The Falcon T Series lock does not have an RX switch available.:
How do I identify the old Falcon T lock chassis versus the new T lock chassis?
Resolution:
The date of manufacture printed on the chassis cover (see below), will determine if you have a revised or old chassis. Chassis manufactured mid-June 2013 will have the new improvements. The first...:
MA lock case dimensions.
Resolution:
See below for commonly requested dimensions on the MA lock. Dimensions not found in other literature have a square around them. CL refers to "Centerline". :
What is the minimum stile an MA lock can fit?
Resolution:
Depending on the door construction the minimum stile may differ but a safe dimension would be 4-3/4". CUSTOMER must check door construction. The pocket depth requirements of the case is 4 1/2".:
How to build an L-Series chassis.
Resolution:
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...:
Explain the function for the L9485.
Resolution:
L9485: Latchbolt retracted by key outside or by knob/lever inside. Outside knob/lever always fixed. Deadbolt thrown or retracted by inside thumbturn. When deadbolt is thrown, all keys become ino...:
AD changing Function in the field
Resolution:
-On the AD series offline locks only you can change the lock function from Classroom/Storeroom to a Privacy, office or apartment function out in the field. - This is done via the HHD/SUS using...:
Can you explain the ND53 function?
Resolution:
ND53PD (ANSI F109) Entrance Lock Turn/push-button locking; pushing and turning button locks outside lever, requiring use of key until button is manually unlocked. Push-button locking; pushing ...:
Explain the function of the L9486.
Resolution:
:
What is the SUS feature "Device Template"
Resolution:
See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...:
When was e.Primus discontinued?
Resolution:
e.Primus was an electronic lock system that used iButton credentials to unlock a door. Product was discontinued in July of 2002 with parts were available only for a short time. Product support fo...:
How do you reset an AD-200 back to default?
Resolution:
:
How does Privacy Mode work with Auto-Unlocks?
Resolution:
If the lock is NOT within an Auto-Unlock period when Privacy Mode is cancelled, the lock stays secured.:
How does the ND82 operate?
Resolution:
ND82PD (ANSI F87) Institution Lock Both levers fixed. Entrance by key in either lever.:
How does the S51 operate?
Resolution:
The S51 is a tubular entrance lock with a key outside and a turn button on the inside. Function: Unlocked by key from outside when outside lever is locked by turn-button in inside lever. Inside le...:
What is thermal bow?
Resolution:
Thermal Bow is a temporary condition which occurs in metal doors mainly due to the temperature differential from one side of the door to the other. This may occur in exterior doors when direct sun ...:
Is the XL11-463 still available?
Resolution:
The XL11-463 is no longer available, this was an option for the L series electrified locks to come with a 5 ft. pigtail. :
Schlage AL small format spacer installation requirements.
Resolution:
The Schlage AL-Series SFIC locks require one (1) small format spacer (D500-000) for 7-pin cores and two (2) small format spacers for 6-pin cores. When these spacers are not ins...:
Does Schlage offer ND conversion kits to convert to Classroom Security function?
Resolution:
For all available ND Series Conversion Kit part numbers, click here.:
How many wires does the Von Duprin E7500 lock body have and how are they used.
Resolution:
The Von Duprin E7500 has a total of 8 wires. Two power wires. 12VDC solenoid has yellow wires. 24VDC solenoid has black wires. Six switch wires. Latchbolt monitor switch has three wires,...:
How do you order the L series lock with an ADA thumbturn?
Resolution:
Effective December 9, 2019, Schlage L Series mortise locks with a thumbturn will ship standard with our new ADA thumbturn. The new ADA thumbturn is slightly smaller than the existing design w...:
What is the difference between the classroom and storeroom functions?
Resolution:
ANSI F84 Classroom Lock Outside lever locked and unlocked by key. Inside lever always unlocked for immediate egress. ANSI F86 Storeroom Lock Outside lever fixed. Entra...:
What is the difference between Night Latch (NL) and Class Room function?
Resolution:
Night Latch (NL)= key retracts the latch momentarily to allow entry. When key is removed, the latch will extend and locks the door (momentary unlock). Class Room (Lock/ Unlock)= key unlocks...:
Why does my 7500 retract the latch bolt but not re-lock the trim?
Resolution:
Tips for changing the function: The NL Drive screw will not be visible when lock body is set to Classroom function There is locktite on the screw that makes it seem like its turned down enou...:
Upgrading any AD-Series lockset to an AD300 - power restrictions
Resolution:
Connect 12VDC or 24VDC power supply to the AD300 lock before attempting HHD communication.:
Is the Schlage Latitude and Longitude lever available in a stainless steel finish?
Resolution:
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.:
What parts are modified when ordering an ND extended lock?
Resolution:
Only the chassis components are modified for thicker door applications, the lever and spindle assemblies remain intact. The following parts may be modified depending on the function of the lock ...:
Available kits to convert classroom mortise locks to classroom security locks.
Resolution:
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077. The...:
How do you order the ND series lock with a small format core?
Resolution:
The letters GD, HD, BD, or BDC should be put after the lock function. EXAMPLE: ND53BD GD = Schlage SFIC core HD = Construction core BD = Less core BDC = Plastic temporary construction core:
What parts are needed to install an L lock on an 1 3/8" door?
Resolution:
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped. The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...:
Is the new Falcon T Series latch compatible with all available T lock strikes?
Resolution:
The new Falcon T-Series latch, introduced mid-June 2013, will work with all available T lock strike options. No changes have been made to the strikes.:
Can the AD-Series and CO-Series magnetic card credential readers be set to read data from different magnetic card tracks?
Resolution:
Customers will need to use the Schlage Utility Software (SUS) on the HHD lock programming device to set the desired magnetic track to be read for access control, if not using default Track 2&n...:
How can the Von Duprin 98/9975-L with 996L classroom trim function be converted as a night latch function in field?
Resolution:
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as se...:
What is the most common practice for running electric power from a frame to the door and hardware?
Resolution:
Electrical hinges or a power transfer units are the most commonly used practices to run electric power to locks and/or strikes. Electric Hinges: Most electric hinges will fit into...:
Can I use the 10-072 strike with a L400 Series lock?
Resolution:
Only the 10-079 or 10-078 strike should be used with the L400-Series. :
How do you remove an AL lock from a door?
Resolution:
AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...:
How do I specify the small rose on a W lock?
Resolution:
In order to differentiate the small rose offering from the standard W lock, add (SR) to the beginning of the lever style. For example, to order a W501PD with a small rose ...:
How do I identify an AL lock?
Resolution:
The AL-Series has four distinguishable parts that can help in lock identification. 1. The AL-Series will have a castle nut holding the chassis on the ...:
Do I have to couple each lock with the HHD/SUS after the coupling password is changed or updated?
Resolution:
After updating the SUS coupling password, subsequent HHD’s will need the new coupling password entered before they can update any information in the lock, once the HHD has the correct coupling pass...:
What are the steps to remove an S lock from the door?
Resolution:
Remove the inside rose then remove the two mounting screws and the inside and outside chassis will come off the door. See Installation Instructions here.:
How does a classroom deadbolt lock operate?
Resolution:
Classroom Deadbolt Lock (ANSI Function: E0171 for B663/763/863 and D111, E0172 for B563 and D211 )Deadbolt thrown or retracted by key outside. Inside turn unit will retract bolt only. Bolt au...:
Resetting a CO200 / CO250 Series Lock back to Factory Default Settings
Resolution:
1. Press and hold the Schlage button. Wait for the lock to beep twice and two green blinks of the Schlage button, indicating a confirmation. 2. After confirmation signals, release the Schlage butt...:
What process should be followed to change the Credential Reader type on a AD-Series lock?
Resolution:
The process to change the Credential Reader on an AD-Series lock is as follows: Note: To ensure firmware compatibility of the lock and reader, it is important that the firmware in the LOCK and the...: