Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
what is this finish?
”
RELATED FAQS
Question
Answer
Is there a conversion kit to make 94/95 devices into a QEL?
Resolution:
Yes. Required Series 94 or 95 Fire or Panic 3FT/4FT or 2 ft 6 in / 2 ft 10 in Finish Optional LX switch &nbs...:
Is the 1990 a direct replacement for the 990 Exit device?
Resolution:
Yes, the 1990 is the direct replacement for the 990 devices.:
What do you do if rust spots show up on steel doors and frame material?
Resolution:
During the construction cycle, spot rust is usually attributed to either material handling damage or improper storage of the material on the jobsite. The material must be repaired and repainted as ...:
Are factory finished doors and frames available from Steelcraft?
Resolution:
Factory finished painted doors are available from Steelcraft. Frames "are not available" factory finished from the factory.Doors are offered in variety of standard colors or can be finish...:
What is the part number for an ND lever?
Resolution:
ND-series locks manufactured prior to January 30, 2017:03-030 - Closed03-031 - Privacy, Cylinder- Schlage KIL (P,L) & Push or Push & Turn Button03-032 - Schlage FSIC 03- 000 - Schlage ...:
What questions should be asked to determine which Von Duprin 6000 series electric strike I have?
Resolution:
See Catalog to identify specific model: Von Duprin Electrical Security Products and Accessories Catalog:
Selected the wrong lock model (CO-200 or CO-220) when updating CO Firmware.
Resolution:
For any CO-200-40 Privacy or CO-220-75 Safe School lock that was manufactured before May 2014: When updating the lock's firmware to CO.A.12 or later, SUS will first ask the question “Is this a CO-...:
What is the part number of the most recent SE track?
Resolution:
The SE series track is the same for all models. It is ordered by the closer model, followed by a -3038. Example -- 4040SE-3038 (specify voltage & finish) or 3130SE-3038 (specif...:
When was the ME high residential and 505 finish discontinued?
Resolution:
The ME trim was discontinued in 2001 and no longer available.:
Can I change an AD lock from an 8 "AA" battery pack to a 4 "AA" battery pack?
Resolution:
The AD lock battery pack type can be changed following this procedure:1. Disconnect the existing battery pack2. Depress and hold the SCHLAGE button for a few seconds to drain off any residual...:
How do you order a Senior Swing header for a 2810 on one leaf and a 2010 on the other?
Resolution:
LCN does offer a 2810 Senior Swing / 2010 manual closer combo for a pair of doors. Both units contained within the same Senior Swing header. To order a paired operator with a 2810 o...:
Does the push bar end cap come as a separate item or do you have to order the push bar kit on the 33/35A or 98/99?
Resolution:
How to order: specify devise type, size, and finish. Example: PBKIT 33A 3' US28:
When were 313AN & 315AN anodized finishes changed to SP313 (695) and 622 powder coat finishes?
Resolution:
Beginning December 6, 2010, all 33A, 35A, 98 & 99 devices ordered as 313AN Anodized was furnished in SP313 (dark brown powder coat). All devices ordered as 315AN ...:
Can you get the ND series lock in a 609 finish?
Resolution:
As standard the ND lock is not available in a 609 finish.:
What doors are available with monorail preps?
Resolution:
Monorail cutouts are only available for non fire rated applications.:
What is the part number for the 99L to 99L-2 kit?
Resolution:
Format for ordering double cylinder (-2) and double cylinder with security indicator (-2si)(device) (fire rated)(-2 or -2si)(conversion kit)(finish)(handing) Examples:98/9927-F-2-Conversion Ki...:
What parts of the device and trim for the 98/99 are 643E finish?
Resolution:
Device: Pushbar end caps, pushbar trim and center case cover. Trim: Lever assembly, trim plate assembly (trim plate and bushing sleeve).Bronze Finish Comparison:
Are stainless steel doors and frames available?
Resolution:
Yes, stainless steel doors and frames are available. Door Construction: LS-Series: Visible edge seams Door construction similar to the ...:
Does Von Duprin offer an exit device for exterior use?
Resolution:
Von Duprin now offers the Outdoor Defense (OUT) option for its 98/99 rim and 98/9927 surface vertical rod exit devices. The OUT option protects an exit device's critical operating components ...:
How can the Von Duprin 4854 mullion be ordered when using the 6300 electric strike?
Resolution:
:
Can you convert a 4040SE with a 120 volt track (solenoid) to a 24 volt track (solenoid)?
Resolution:
You can not convert an SE track to a different voltage in the field as the "solenoid " in a 4040SE track is not field replaceable. The complete track will need to be replaced. :
What finish is brushed chrome?
Resolution:
A 626 or US26D. Schlage definition of the 626 is a satin chromium plated finish.:
Do we offer the Ives butt hinges in 609 finish?
Resolution:
The 609 finish is not available with Ives butt hinges.:
Does Steelcraft prime paint doors and frame?
Resolution:
All Steelcraft Frame, Door and Architectural Stick components will receive one coat of sprayed-on factory paint which is a baked-on, rust-inhibited primer that conforms to the industry standard ANS...:
Is there an Exit Alarm Retrofit Kit (EAK) for the 19 series?
Resolution:
These kits for the 19 Series were discontinued June 11th, 2012 when the updated alarm kit for the 24/25 series was released. Prior to discontinuation, it was o...:
Can Steelcraft doors be powder coated?
Resolution:
Steelcraft does not offer factory powder coated doors and/or frames. Powder coatings usually require heat between 300 to 400 degrees to melt and cure the powder coat. The higher heat can ca...:
Are Graintech doors available with GrainTech on one face and standard panels on the others face?
Resolution:
GrainTech® doors are not available with different finishes on the inside and/or the outside door panels. Both panels must match.Standard GrainTech® finishes include:BirchAshOakMapleM...:
Is the old Doromatic 1090 the same as a 2090?
Resolution:
Yes, with the exceptions that the 2090 base material is aluminum whereas the 1090 was either brass or bronze base material depending on the finish.:
Can you replace just the solenoid in the 4040SE, 4040SEH, 3130SE, 2310ME, 4310ME?
Resolution:
The solenoids are not replaceable by themselves but can be ordered with a subassembly. On the SE products the track must be replaced, specify finish and voltage On the ME products the cylinder mus...:
What is the part number for the blocking ring for use without compression ring?
Resolution:
The part number for a Schlage mortise cylinder blocking ring for use without compression ring is the 36-079 (specify dimension and finish).:
What is a mechanical Lock?
Resolution:
A lock is any device which prevents access or use by requiring special knowledge or equipment. Mechanical locks are mechanical devices which secure an opening by keeping a door closed until a rel...:
What is the part number for QEL94/95 inpact conversion kit?
Resolution:
The part will be configured as CONVERT.XXXX part numbers. The customer need to specify the following criteria. Required: Series 94 or 95, Fire or Panic , 3 feet/4feet or 2 feet 6 inches/2 feet...:
What is the CO-220?
Resolution:
The Schlage CO-220 is standalone classroom lock down solution with remote fob and visual indicator which allows immediate local lock down by simply pushing the button on the remote fob from anywher...:
How do I retro fit the 2390 into the 1390 muntin?
Resolution:
Replace the device and vertical rods with the current 2390 device and possibly a filler plate. A filler plate may be needed as the older 1390 device was sized per order whereas the 2390 is onl...:
What is thermal bow?
Resolution:
Thermal Bow is a temporary condition which occurs in metal doors mainly due to the temperature differential from one side of the door to the other. This may occur in exterior doors when direct sun ...:
What is the difference between the Ives 482B and the 482A door guards?
Resolution:
The difference between the Brass version 482B and the Aluminum version 482A is the size and design as well as the base material and available accessories. The Brass version 482B comes w...:
What are the LCN standard finishes?
Resolution:
White Powder Coat can be ordered as a special RAL finish with a metal cover.:
Are top caps, bottom caps and/or astragals finish stained when factory attached on Graintech door?
Resolution:
When factory installed on GrainTech® doors: Finish Stain - YES, top caps, bottom caps and astragals are stained (prior to attachment) to match the GrainTech® door finish. GrainTech® Steel - NO, t...:
What causes doors and/or frames to rust?
Resolution:
Prime or painted surfaces which have been scratched or otherwise marred during installation (including field welding) and/or cleaning must be field repaired and re-primed by the installing contractor.:
What exit device is weather rated?
Resolution:
The Von Duprin 98/99 rim and 98/9927 surface vertical rod exit devices are now available with the Outdoor Defense (OUT) option.Devices with the OUT option have a specialized coating applied to mech...:
Will the Von Duprin 7500 mortise lock replace an old 34 or 58 lock body?
Resolution:
The Von Duprin 7500 mortise lock body will replace the old style 34 and 58 lock bodies. Order a 7500 mortise lock in the proper finish. The old style strike must be replaced with 575 strike becau...:
What powder coat best matches US10B for a closer?
Resolution:
The closest powder coat finish by LCN is Dark Bronze (BHMA 695).:
What is the part number for the inside lever on an L9000 lock?
Resolution:
The part number is the 09-402, specify the design and finish.:
What grade of stainless steel do we use in the levers on L9000 locks?
Resolution:
Schlage offers 629 and 630 stainless finishes on levers for the L-Series only. These levers are made of 303 or 304 grade stainless steel.:
What are the part numbers for the inside and outside knobs for the L series?
Resolution:
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish:
What is the 689 finish?
Resolution:
The BHMA standard 689 is an Aluminum finish, and is silver/gray in color.:
What is the Senior Swing 9540 REG arm part number?
Resolution:
The part number for the threaded rod "only" on the Senior Swing regular arm is 9540-82, 9550-82, or 9560-82 or -82L for the long rod option. The part number for the threaded rod, turn buckles, an...:
What cylinder is used for the Von Duprin -2 double cylinder function?
Resolution:
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2.Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an&n...:
Do we have parts for the old multi-piece center case cover for the 98/99 series devices?
Resolution:
Von Duprin does not offer the old two piece center case cover any longer. The new center case cover will work on the old two piece cover device. Order the following parts: New 1-piece cover ...:
Warranty information on Allegion Commercial products.
Resolution:
See here for our Warranty Information. :
How do I enroll a user in HandNet for Windows?
Resolution:
In order to enroll a user in HandNet for Windows, you will need to: - Log into HandNet for Windows (default login: username: 1234 password: new )- From the menu at the top, click...:
Can steel frames be installed after the wall board is installed in stud wall applications?
Resolution:
DW and K-Series frames are designed to slip onto a stud wall after the wall is finished (painted, wall papered, etc).Walls can be either wood stud or steel studUsed only for interior appl...:
What is the part number for a blade stop shim for a 6111 or 6113 electric strike?
Resolution:
010055-xx is the part number for Blade Stop Shim kit for 6111 or 6113 electric strike and it must be ordered separately. xx is for the finish callout.:
What finish will the strike and latch be if ordered with a split finish?
Resolution:
The door handing determines the finish of the latch and strike. Left reverse and right reverse doors default to outside trimLeft and right hand doors default to inside trimIf lever and ro...:
What are the 1460 closer arm options?
Resolution:
The 1460 Regular Arm part numbers are: Regular Arm -- 1460-3077 or 1460-3077L for long arm (must specify finish). Regular Arm with PA -- 1460-3077PA (must specify finish). Regular Hold Open Ar...:
What is the part number for a Schlage FSIC lever on an ND lock?
Resolution:
On ND Series locks manufactuered prior to January 30, 2017:The ND FSIC lever part number was 03-032. :
Are the Pushbar Retrofit Kits (PBKIT) the same for 98/99 and 33A/35A series devices?
Resolution:
A PBKIT is a Pushbar Retrofit Kit.The pushbar retrofit kits are not the same for 33A/35A and 98/99 series exit devices. Depending on the finish of the exit device, the pushbar end caps are di...:
Can I get Falcon locks in a 612 finish?
Resolution:
Effective Feb 25, 2008 Falcon no longer offer a 612 finish on any product.:
What is the part number for the 1490 push sticker?
Resolution:
The part number depends on the handing and finish of the device: RHR, US28 is #4270107321 LHR, US28 is #4270107323 RHR, DC13/DC35 is #4270107320 LHR, DC13/DC35 is #4270107322.:
What types of steel are used in commercial steel doors?
Resolution:
The three most common steel types are cold rolled steel, galvannealed steel, and galvanized steel. Cold Rolled Steel (CRS) is suitable for most interior applications, is uncoated steel a...:
What is the part number for the armor mounting screws for the L lock?
Resolution:
The part number is K110-020 (includes 2 screws). You will also need to specify the finish.:
Are the 643e and 716 finishes the same?
Resolution:
The commercial Aged Bronze finish (643e) is the BHMA equivalent to a copper plated, blackened, relieved and then clear coated product. This commercial finish is identical to the residential Aged ...:
What is the part number for the plate and the 2030 cylinder?
Resolution:
Part numbers listed below: 2030-3071 cylinder assembly includes the closer cylinder and finish plate. 2030-3971 is the cylinder only. 2030-3002 is the finish plate. 2030-3077T is ...:
Steelcraft field paint instructions
Resolution:
Steelcraft frames and doors are furnished with a high grade, low gloss, baked-on prime paint that provides the best possible protection against corrosion, abrasion and weather, and is an excellent ...:
Is the EDA or Cush arm with threaded studs still available?
Resolution:
ST-3195 is used to obtain the old style EDA or Cush arms which were assembled with threaded studs so that you could take apart the arm assemblies. Our current standard EDA and Cush arms are rivet...:
Does EL or QEL conversion kit for Von Duprin exit devices contain mechanism cover plate?
Resolution:
The conversion kit does not contain a new mechanism case cover plate. If a cover plate is desired, you would need the Fire or Less Dogging Cover Plate for EL/QEL conversion kit and Panic cove...:
What causes excessive pinhole rust to start showing up on steel frames?
Resolution:
CAUTION must be used in investigating this problem - In most cases, excessive field rusting of products is caused by improper storage at the jobsite. That situation must be validated prior to refus...:
What is the difference between galvanized and galvannealed steel?
Resolution:
Galvannealed and galvanized steel are zinc coated at the steel mills and are designed for rust and corrosion resistance. Both steels are passed through a hot dip coating process for rust prevention...: