l series mortise spring

RELATED FAQS

Question
Answer
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1.     Spindles and Springs   Part Number  Description  L283-060 Spindle and spring, 1...
You can order an L lock with a lever on one side and knob on the other as long as it's still rose by rose, or escutcheon by escutcheon (must be same style escutcheon). EXCEPTIONS: Knob trim on the...
Includes the SL1 lever on one side and the SK1 knob trim on the other side.
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped.  The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...
The L series armor fronts are only available with square corners.  
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish
UL Listed for 3-hour fire door (except L9076 and L9077)
Typically for a 1-3/4" door you would use a 1-1/4" cylinder.  Use the Table in the Pricebook for a reference:  
Typical installation by an experienced Schlage L lock installer on a door correctly prepped for the Schlage L-Series function could take 10 to 20 minutes.  Many outside variables can change the amo...
The springcage part number is L283-040.
Only the lever return spring is available.
Related solution: What is the part number for the lever return spring for the old M series mortise lock?
See Falcon MA lever assembly below: The spring mechanism (E) returns the lever to horizontal.  The parts are not sold separate, so if the lever sags, the entire lever assembly shoul...
Lever assemblies part numbers are found in the Pricebook.  Note they are handed.
The 20-001 is a conventional mortise cylinder with a straight cam, compression ring and spring for use on rose trim. For use with the L9060 outside cylinder or other straight cam applications.
The 30-001 is a conventional mortise cylinder with a clover cam, compression ring and spring for use on rose trim. For use with the L9000 mortise locks except for the L9060 outside cylinder.
Maximum nominal (overall) single door sizes are as follows: L-Series (Laminated Door) 20 Gage = 3’ 0” wide X  8’ 0” high 18 Gage = 4’ 0” wide X 10’ 0” high 16 Gage = 4’ 0” wide X 10...
Raceway availability: Optional factory installed raceways are available in doors but are not available in frames. Preparation Info: Steelcraft installs a flexible 1/2" ID steel conduit through the...
Supply wires - 22AWG
RX wires - 22AWG
LX wires - 22 AWG
All functions except L9463 and L463: Add L583-363 to the part number 09-509 L583-363 for the turn only or L9453 07L 626 L583-363 with a lock The L583-363 part number is an option and can not...
To convert a Schlage mortise L9080 function to a L9070 function purchase and replace the following:   L283-133, L9070 lock case  L283-040, spring cage (for outside lever)
The L-Series doors are designed for virtually all construction requirements in commercial building applications. They have also been tested and approved for uniform wind load per ASTM E330.  ...
RX wiring on all L9000 locks with RX switch manufactured after January 2, 2017:The L-Series switched to a handed modular three-wire request to exit (RX) switch. This change was originally completed...
Specific to the RX switch installed into the L9080EL/EU and L9082EL/EU and L9000 mechanical locks prior to January 2, 2017:ALL PART NUMBERS BELOW DISCONTINUEDThe L-Series switched to a three-wire r...
The inside lever mounting plate part number is L283-031.
The SL-Series door is a square edge non-handed door. A Hinge Filler  (also referred to as Hinge Spacer) is the small removable trim part located on the door between hinge leaf and hinge reinforcem...
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
Door cores are available as follows: L-Series SL-Series and A14-Series Doors: Honeycomb core is standard Polystyrene core is optional Polyurethane core is optional CE-Serie...
Yes, stainless steel doors and frames are available. Door Construction: LS-Series: Visible edge seams Door construction similar to the L-Series LSW-Series: Seamless with we...
The minimum stile and rail dimensions are to exposed glass are: Stiles = 6 13/16" Top Rails = 6 3/4" Center Rails = 7 1/2" Bottom Rail = 10 3/4" For high traffic and high abuse locations th...
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series.  Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...
The replacement solenoid for the Schlage L-Series mortise lock is part number L283-053.
Indicator not extended Indicator extended
The indicator on a cylindrical hotel lock is a small pin that projects outward from the face of the cylinder plug (Figure 1) when the inside push button is depressed.  When this pin is pr...
SCHLAGE locks are available with the following backsets: Lock Series Lock Type                 ...
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
The lever removal tool can be used to remove levers in both the ND and the L Series mortise locks.
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project.  This tool can be used for Schlage ND-Series ...
A lock is any device which prevents access or use by requiring special knowledge or equipment. Mechanical locks are mechanical devices which secure an opening by keeping a door closed until a relea...
A UL 20 minute fire rating is the maximum fire rating for a Full Glass (FG) door design. A14-Series door construction: Max fire rating is 20 minute. UL label only FG must use Over-Lapping Stee...
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077.  The...
All Von Duprin 370 Series trims require a 1 1/4" mortise cylinder with a straight cam.
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.
Screw part number is L583-485.  Screw type: 8-32 UC-2A W/#6 Flat truss head Phillips recess, header point.
Monorail cutouts are typically the upper corner of door. Channels are cut to size welded into door held flush to cutout. We do not supply any covers or plates to finish.
The size monorail cutout is 8" wide x 24" high
Monorail cutouts are only available for non fire rated applications.
BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegion...
Country of Origin (COO) information can be found in the Buy American Act (BAA) brochure.
To obtain product certification forms:Download the BAA Catalog on the Allegion website Complete the information requested in the the BAA Catalog with a detailed copy of the prod...
Steelcraft does not supply door louvers (loose or installed) and will only provides a cutout in doors for specified louvers sizes.
Stamped louvers are no longer available from Steelcraft in any door series. Steelcraft discontinued this offering in 2008. Steelcraft will only provide a cutout only in doors for louvers.
The 09-611 indicator stands off the door 0.39".
The pricebook suggests (for a 1-3/4" door) using a 1-3/8" cylinder when installing with an 09-611 occupancy indicator.
To determine Actual Door Size, the following values are subtracted from nominal door size (frame opening/order size) Actual Door Size: The largest measured width by height of the door leaf as m...
Reference the L-Series Service Manual to change lock functions or build up a case from parts.
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...
Lockcase dimensions (depth x height x width) are: L/LV9000 -  4 7/16" x 6 1/16" x 1" L400 -  4 7/16" x 3 5/8" x 1"
 Mounting Posts   Part Number  Door Thickness  L583-211  1 3/8"  L583-212  1 3/4" - See note section on SL1 trim  L583-213  2...
The ND-Series RX,  the L-Series RX and latch monitoring switches are Form C - Single Pole Double Throw (also known as SPDT).
All doors are tested in accordance with ASTM C1363 and SDI 113:B18 Series (Steel Stiffeners)     U-Factor = 0.50     R-Value = 2.01B16 Series (Steel Sti...
L20, L18, L16, L14, LF20, LF18, LF16, LF14, LW18, LW16, LW14, L Series ; Laminated Door, Beveled Edge
SL20, SL18, SL Series; Laminated Door, Square Edge, Non-Handed Door
The old D series springcage part numbers are as follows: C303-035 - Inside Springcage C303-036 - Outside Springcage These parts are no longer available.
Yes, the spring torque on 3SP1 butt hinge is adjustable.  See instructions at this link:https://static-or01.inbenta.com/fc7332911aa38d5387ffdef79e8605c6ecdc727ece31acf5bc8e26dcac5d29e4/Iv...
In 2002 the Schlage AL-Series underwent a design change that affected the spring cage, driver, and plastic insert.  Spring cage and driver replacements for AL locks manufactured before this design ...
The JD YA6 tailpiece is intentionally designed such that the tailpiece cannot be installed at the same time as the cylinder.  Interchangeable cylinders assume that the lever and taipiece is in...
See the JD Yale Lever installation instruction HERE
How to:  What are the steps to adjust a door closer?Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment.  All closers with a "Delay" feature ...
Issue: One or both levers don't stay horizontal and droop down.Facts: Falcon T series locks in a high use application.Cause: Weak or broken springs within the springcage.Solution: Replacement sprin...
ND -series locks manufactured on or after January 30, 2017 use the following spring cages:Outside - N523-218 - For ALL cylinder options except for JD-YA6, JD-YA7 and JD-MEDInside - N523-222 -...
ND-series locks manufactured before January 30, 2017 used the following spring cages:
You can replace the 6210 spring and lip, part number 050940-00.
The part number for the Spring Cush block assembly is: model number-3080. EXAMPLE: 4110-3080
The Date Code and Closer Size are stamped in the backside of the closer body. Closer Size: If the number is "1", the closer is a 2031 or 5031. If the number is "3", the closer is a 2...
All the 2030 series closer have a fixed spring sizes. Example -- a 2031 has a size 1 spring,  a 2302 has a size 2 spring, 2033/2034/2035 etc. All the 2030 series closer are shipped at the weakest s...
The spring itself is not replaceable, you would need to replace the 19 centercase assembly.