Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ do you have operation and manual on mechanical hardware? ”

RELATED FAQS

Resolution: CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus. :

What is clear opening width?

Resolution: Clear Opening Width for swinging doors is measured (with the door open 90 degree) from the face of door to stop soffit on strike jamb. &nbs...:

What's needed to write a door hardware specification?

Resolution: The following items are needed for Spec Writers to write a door and hardware specification Building code being used Occupancy type or types Occupancy load for any rooms or areas of ass...:

Does Allegion write specifications and specs?

Resolution: Allegion does provides professional support to Architects and Design Professionals. For information related to specification development and support, Website for Architects and Desig...:

What is GrainTech?

Resolution: GrainTech® is a Steelcraft door option which provides a wood grained pattern which is embossed into both face sheets of the door. GrainTech doors are factory stained and top coated with a cle...:

What causes the top rod case to pull away from or strip out of the face of a steel door?

Resolution: Hardware falling off a door is caused by one or all of the following issues: Field abuse Improper internal reinforcements in the door Improper field preparation The top or bottom rod case can...:

What options are available on the CE-Series doors?

Resolution: CE Series door in a variety of embossed panel designs and gages. The CE series embossed panel doors also offer a wide range of specifiable options including sizes, and hardware prepar...:

Does Von Duprin offer an exit device for exterior use?

Resolution: Von Duprin now offers the Outdoor Defense (OUT) option for its 98/99 rim and 98/9927 surface vertical rod exit devices. The OUT option protects an exit device's critical operating components ...:

Why can't I get my JD YA6 cylinder to install into an AD-Series lock?

Resolution: The JD YA6 tailpiece is intentionally designed such that the tailpiece cannot be installed at the same time as the cylinder. Interchangeable cylinders assume that the lever and taipiece is i...:

What is the difference between Panic Hardware and Fire Exit Hardware?

Resolution: The most obvious difference (in the device) is the lack of mechanical dogging on a Fire Rated Device. There are some internal parts that may be different and the method it is secured to the d...:

Are GrainTech doors available with hardware preps?

Resolution: All hardware options (available on standard door) are available on GrainTech® doors. Available hardware are covered in the Steelcraft Price Manual. GrainTech® doors can be prepped for the Von Dupr...:

Is there adjustment limits on the regulation valves of LCN manual closers?

Resolution: The regulation valves are designed to adjust the flow the hydraulic fluid in the closer which regulates the door closing speed through various phases of the closing cycle. The regulation valv...:

When are Panic Devices required?

Resolution: The use of Panic Hardware and/or Fire Exit Hardware is required by the International Building Code (IBC) and NFPA 101 – The Life Safety Code, depending on which code and which edition of the code i...:

What is delayed egress hardware?

Resolution: Delayed egress hardware prevents a door from being opened from the egress side, usually for a period of 15 seconds. This type of device is often used to prevent theft, while maintaining life safe...:

Will a 4640 operator open the door in windy conditions?

Resolution: The 4600 operator is designed to meet the ANSI Code 156.19 that limits the opening force to a 15 lbs. By code and design, the operator must stop opening the door when an obstruction or resistance ...:

What causes the error "Device does not support this action - E802" when I'm coupling an AD lock?

Resolution: In order to properly couple, the interior pushbutton must be held down while tapping the SW1 (tamper switch) three times. This will enable the lock to couple to the HHD.: