***The 6210 electric strike was designed to replace mechanical strikes in existing openings when access control is desired.***
Note: The Best 40H series lock is not listed on the 6210 electric s...
None of the Von Duprin electric strikes will work in a retrofit application where the normal standard mechanical strike is mounted to the frame because none of them are thin enough to fit in...
For all models of 6000 series electric strike, except the 6300 & 6400, the color of the solenoid wires determine the voltage.
Black wires are used on 24VDC solenoids and yellow wir...
Electrical hinges or a power transfer units are the most commonly used practices to run electric power to locks and/or strikes.
Electric Hinges:
Most electric hinges will fit into...
The 4600 Series operator has both a 12VDC and 24VDC output rated at 1A (combined load) to power strikes, maglocks, and other devices, but an EL device "always" has to have a separate PS914-2RS Seri...
The 5100 strike details are listed below:
Only operates with 12VDC or 24VDC power supply.
Will not operate with AC transformer.
12 or 24VAC can be converted to 12/24VDC using Von Duprin SO12 o...
The Von Duprin XP98/99 device uses a different strike than standard 98/99 device.
The 909 strike is for non fire rated XP devices and the 954 strike is for the fire rated XP device.
49/9954 mul...
The 6111 electric strike can be used only on non rated openings less bottom rod with pullman top latch (use ES prefix when ordering device). Device back set will change to match the centerline of t...
Von Duprin surface mounted 6300 electric strike paper template and installation instruction are provided with the electric strike. See attached
https://us.allegion.co...
The strike will always be DC. By using a SO24 or SO12(rectifiers) you will be able to convert the AC waveform from a transformer to a DC waveform that will be acceptable by the 6000 series strikes.
The Von Duprin 6111 electric strike would work with DOM 1790 device on medium style doors
Centerline of the 1790 device mounting screws are located 1 11/16" from face of stop. See d...
You can't run 24VDC into the 12VDC electric strike, over voltage such as this will cause the solenoid to heat up and damage the solenoid. You must change to a 24V solenoid, part number 050240-00.
To convert the Von Duprin 6000 series electric strikes from FS to FSE or from FSE to FS follow these steps:
Remove the electric strike face plate.
Remove the strike b...
Part numbers:
FS slider, part # 090591 (Use for all EXCEPT 6211WF/6212WF/6221/6223. See 090798 below)
FS slider, part #090798 (Use this slider for FS models 6211W...
Follow these questions to determine which Von Duprin electric strike model you have
1. What type of hardware is latching to the electric strike?
2. Single or pair ...
See Catalog to identify specific model: Von Duprin Electrical Security Products and Accessories Catalog
The Von Duprin 6210 electric strike was designed for retrofit applications and will not work with the Falcon MA series lock when strike and lock body are mounted at standard locations (centerline o...
The following application information apply to the 5100 electric strike:
Can only be used on a single door with a cylindrical lock
Can not be used on a pair of doors
Can not be used on a mullion
The 22, 33/35A and 98/99 rim exit devices:
The 6111 is the most common electric strike to be used with these devices
6112 and 6113 electric strikes also could be used
The 6300 surface mount el...
This is not a recommended application as the electric strike does not have the same holding force as the XP98/99 rim exit device. Typically the XP device will withstand a higher force than electr...
The DS is Dual Monitor Switch for Von Duprin 6000 series electric strikes.
DS option cannot be added to a Von Duprin 6000 series electric strikes in the field. It is only available factory inst...
The 6216 electric strike was designed only for use with only the Folger Adams 310-3-1 mortise lock with deadbolt. The dead bolt must be retracted manually for the the strike to operate.
Von Duprin doesn't offer any electric strike to fit into 1 1/2" aluminum/metal faced frame. Minimum requirement to install 6211/6211AL is 1 15/32" mortise depth.
The Von Duprin 6000 series electric strike has a 12 or 24VDC solenoid with plunger, spring and impact washer as shown 6000 solenoid
Make sure the solenoid spring and impact washer are not missin...
An electric strike or maglock (24 volt only) can be wired to a Senior Swing 2800/9500 series operator using the P10 Lock Interface cable.
To power the 24VDC electric strike or maglo...
The Benchmark III control has a 24VDC, 2.5 amp power supply, and built in relay for controlling electric strikes or other accessories less than 2.5 amps current load.
For a fail secure strike, r...
The 5100 electric strikes are for use with cylindrical locks only. Instead use the following:6211 electric strike is used with mortise lock without deadbolt on a new single door, hollow ...
The Von Duprin 6000 series electric strike can be converted by ordering the appropriate kits below. Kits include the solenoid, plunger, spring, and washer.
6000 Series solenoid Kit 1...
Von Duprin 6223 electric strike is the most common closed back strike or the 6221 for open back strike on inactive leaf that can be used with Schlage L9000 or Von Duprin 7500 mortise lock.
Option boards are not required with PS900 series power supplies when using electric strikes. See the list of options below.
The PS902 would power up to 5 electric strikes at 24VDC or&n...
Follow the steps below to troubleshoot the problem. Measure the voltage at the electric strike. If the strike is FSE and not locking there should be no voltage at the strike and if it is FS there ...
The 8200 Series operator CANNOT power a strike, maglock, or EL device. A separate power supply is ALWAYS required. There is an onboard relay to control a strike, maglock, or EL device.
Schlage offers the 10-042 Electric strike, 1 1/4" x 4 7/8", 606 and 626 finish only.
Related solution: What are the current and voltage requirements of ...
The 4630/4630 operator has a 12 VDC and 24 VDC output that can power an electric strike or maglock. The wiring diagrams are shown on page 14 of the installation instructions (attached).
4600 Insta...
The 5547 device can be ordered with an ES prefix to work in conjunction with an electric strike. This requires LBR and can only be done on non-fire rated applications.
To convert an existing ...
If the solenoid of the 6000 series electric strike is powered continuously with proper voltage at room temperature, the solenoid can feel very warm to the touch. Ensure the power supply ...
The Locknetics 9100 series electric strikes are replaced with Von Duprin 6211 and 6210 electric strikes.
The 6211 is used if the frame is being replaced. The 6210 is for ...
The Falcon 25R rim device can be used with 6111 electric strike on single or double doors.
Additional Information:
The Von Duprin 4854/9854 mullion is required when using 25R...
For the backset see the Falcon (F)25-R template; T-1201 for Metal Door, W-1201 for Wood Door.
For Single Doors, the distance from the surface of the raised stop to the Centerline of the device is...
The power supply output in the 7900 series control box is a 12VDC output, rated at (1/4A) 0.250A. It cannot be used to power a strike or maglock. You need to have a separate power supply for the st...
The 6211 would be the most common electric strike to be used with cylindrical locks on a single door application. Check the template to confirm compatibility with specific cylindrical lock model n...
The Von Duprin 1609 cannot be used on a pair of fire rated doors. We recommend using the Von Duprin fire rated mortise exit device in lieu of the rim device such as the Von Duprin 5575-F,...