All LCN metal covers are steel which is a Ferrous material. FerrousThese are metals which contain iron. They may have small amounts of other metals or other elements added, to give the ...
Grouting frames is:
A process done in the field during hollow metal frame installation
The internal cavity of the frame is fill with masonry or mortar
It is intended to mainly provide ...
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function:
Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as se...
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUOvervoltage will cause the lock to shut down for approximately 5 minutes to allow the circu...
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUThese models require 12/24 VDC with a peak current of 0.4 amps. The following po...
Applies to L9080EL/EU, L9082EL/EU (Discontinued)The Schlage L9080 EU/EL and L9082 EU/EL require 24 VAC/VDC with a peak current of 1.3 Amps at 5 to 10 second intervals and a holding curren...
RX wiring on all L9000 locks with RX switch manufactured after January 2, 2017:The L-Series switched to a handed modular three-wire request to exit (RX) switch. This change was originally completed...
Specific to the RX switch installed into the L9080EL/EU and L9082EL/EU and L9000 mechanical locks prior to January 2, 2017:ALL PART NUMBERS BELOW DISCONTINUEDThe L-Series switched to a three-wire r...
Reference the L-Series Service Manual to change lock functions or build up a case from parts.
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...
The finishes below are available on the L9000, some lever designs and trims are not available in all finishes.
605
Bright Brass
606
Satin Brass
609
&...
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped. The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...
To convert the Von Duprin 9975NL(Night Latch or Storeroom) to 9975L (Classroom) exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL ...
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL screw on 7500 mortise lock counter clo...
L583-446; Schlage Adams Rite MS modular cam used on 1 1/8", 1 3/8" and 1 5/8" cylinders
L583-447; Schlage Adams Rite MS modular cam used on 1 1/4", 1 1/2" and 1 3/4" cylinders
B502-944; Sch...
Outside Knob/Lever and Rose/Escutcheon Assemblies
Part Number
Description
A Rose with Knob/Lever
09-506
Designs: 01 02 03 05 06 07 12 17 18 OME 41 42
09-655
Des...
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
See image, ANSI A115.1 Mortise Lock Prep
This door prep requires the N escutcheon with the L283-029 spacer kit to keep the springcage from falling into the door.&nbs...
There are several Schlage and/or Falcon locks that have been tested and approved for this application.
For Commercial use the locks have been tested and approved as ...
Von Duprin Exit Devices (33A/35A, 98/99, etc) are handled on a case by case basis regarding their ability to handle salt and chemical environments.
Our powder coated finishes US28 (Anodized Alum...
The MA lock does not have Vandlgard or a breakaway trim feature, however, the lever spindle on the MA lock will shear if too much force is applied in order to prevent internal lock damage and resis...
The Schlage Vandlgard option available on select L-Series, LV-Series, and ND-Series and is ideal for areas subject to abuse or anywhere vandalism is likely to be present, such as schools, univ...
Vandlgard is specified by "LV" for mortise locks. The L9000 is a mortise style lock that mounts into a pocket mortised into the edge of the door.Vandlgard is specified by ND9x functions f...
The lever removal tool can be used to remove levers in both the ND and the L Series mortise locks.
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1.
Spindles and Springs
Part Number
Description
L283-060
Spindle and spring, 1...