Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ al lock series conversions ”

RELATED FAQS

Resolution: The new AL FSIC driver part number is A700-052. This driver snaps onto the back of the core similar to the ND, as opposed to it being assembled into the lock chassis with a retaining ring. Th...:

AL-Series Plunger Assembly Instructions

Resolution: Changing the plunger assembly on the AL-Series requires disassembling the chassis. Refer to Plunger Assembly Instructions for guidance.:

What parts do I need to convert my AL lock to fit a 2" thick door?

Resolution: Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...:

What backsets are available on Schlage and Falcon locks?

Resolution: SCHLAGE locks are available with the following backsets: Lock Series Lock Type ...:

What grade is the AL lock?

Resolution: The AL lock is a Grade 2 lock ANSI/BHMA Certified A156.2-2003, Series 4000, Grade 2, UL Listed for 3-hour fire door.:

What process should be followed to change the Credential Reader type on a AD-Series lock?

Resolution: The process to change the Credential Reader on an AD-Series lock is as follows: Note: To ensure firmware compatibility of the lock and reader, it is important that the firmware in the LOCK and the...:

Did the AL series SFIC lever inserts change?

Resolution: The SFIC lever insert part number prior to 2001 was the A700-022.:

What are the part numbers for the new Falcon T latches?

Resolution: Falcon T Lock Latches No Longer Offered With The T Lock Effective mid June 2013 Old Part Number New Part Number &nb...:

Why can't a new spring cage or driver be installed on an older AL lock?

Resolution: In 2002 the Schlage AL-Series underwent a design change that affected the spring cage, driver, and plastic insert. Spring cage and driver replacements for AL locks manufactured before this design ...:

How do you adjust for door thickness on an AL lock?

Resolution: The standard door range for an AL lock is 1 3/8" to 1 7/8". Using the supplied instruction sheet, align the springcage post to desired door thickness by adjusting the outside castle nut. See inst...:

How to build an L-Series chassis.

Resolution: This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...:

Why would the 996L trim not lock or unlock when installed with 98 or 99EO?

Resolution: The 98/99 rim and vertical rod exit devices are shipped with NL drive screw to function as a Night Latch. To convert the device to Class Room, remove the NL Drive Screw on 98/99 center case ass...:

What is the Buy American Act (BAA)?

Resolution: BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegio...:

How do I change an AD-Series lock to a different AD-Series lock type?

Resolution: Re-classing is the process by which an AD-Series device is able to change its lock type. The AD-Series has a modular architecture and a major benefit of this type of architecture is that it allows ...:

What T lock improvements were made in May 2013?

Resolution: In mid-May 2013 the Falcon T-Series changed the slide and catch spring used in the chassis to improve overall durability.:

Can the credential reader be changed on a CO-Series lockset?

Resolution: A Credential Reader MAY be replaced with another Credential Reader of the same type; however, a Factory Default Reset must be performed before the lock will function properly.:

Did the H-Series deadbolt and linkage change?

Resolution: As of May 23, 2011 the Schlage H-Series is assembled with the Schlage B500-Series deadbolt and a new linkage. If the deadbolt is being replaced for a lock manufactured prior to May 23rd, 2011...:

What is a Grade 2 Lock?

Resolution: Grade 2 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 400,000 Certified Cycles ANSI...:

How do I identify an AL lock?

Resolution: The AL-Series has four distinguishable parts that can help in lock identification. 1. The AL-Series will have a castle nut holding the chassis on the ...:

What firmware does my CO-100 lock have?

Resolution: CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus. :

Why does my 7500 retract the latch bolt but not re-lock the trim?

Resolution: Tips for changing the function: The NL Drive screw will not be visible when lock body is set to Classroom function There is locktite on the screw that makes it seem like its turned down enou...:

How to convert a ND series lock cylinder format from PD to BD?

Resolution: On ND locks manufactured on or after January 30, 2017 only the SFIC lever and SFIC driver are needed to convert the lock from Full Size conventional (PD) or Full Size IC (JD, RD, TD) prep to S...:

What drains the AA batteries on an AD-Series lock?

Resolution: Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1) One the four (or eight) AA was inserted reversed and the rese...:

What drains the AA batteries on an CO-Series lock?

Resolution: Causes for AA battery drain in CO-Series LOCKS - Possible Cause Fix/Corrective Actions One of the four AA batteries was inserted reversed and the reserved battery drains the other batteries. ...:

Are ND locks available in 629 or 630 finishes?

Resolution: The AL and ND locks are not available in any stainless steel finishes. The only option is either the 626 satin chrome or 625 bright chrome.:

Is there a tool to drill the thru bolt holes on cylindrical locks?

Resolution: Order the M204-198 thru-bolt jig, see Figure 1. Figure 1: M204-198 thru bolt jig The 40-080 was the old Schlage jig. The 030736-000-70 was the old Falcon jig. When the jig changed to...:

Will an AL lever fit onto an A-series lock?

Resolution: The AL and A trim is not compatible with each other.:

Are Schlage AL series products handed?

Resolution: The AL series product line does not use any parts that requires prior knowledge of the door handing. :

What is the part number for an AL Series cylinder?

Resolution: Refer to table 1 for the list of Schlage AL-Series cylinders. AL-Series Cylinder Reference Table Function Cylinder Mechanism Complete Cylinder Non-Hotel Functions ...:

Will the AL lock fit a 2" thick door standard?

Resolution: The AL series lock fits up to 1 7/8” door thickness out of box.: