Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
where are templates for Ives rescue hardware
”
RELATED FAQS
Question
Answer
Where can Von Duprin 6300 electric strike installation instructions or templates be found?
Resolution:
Von Duprin surface mounted 6300 electric strike paper template and installation instruction are provided with the electric strike. See attached https://us.allegion.co...:
What is the SUS feature "Device Template"
Resolution:
See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...:
Where is the wood template for the 996L-DT ?
Resolution:
There is no template for 996L-DT for wood door. You will need to use the 996L-DT installation instruction or 996L-DT metal template. See attached instruction/template 996L-DT instruction/template.:
Where can I find discontinued G lock templates?
Resolution:
Schlage G Series template locate here. :
What is the most common practice for running electric power from a frame to the door and hardware?
Resolution:
Electrical hinges or a power transfer units are the most commonly used practices to run electric power to locks and/or strikes. Electric Hinges: Most electric hinges will fit into...:
When are Panic Devices required?
Resolution:
The use of Panic Hardware and/or Fire Exit Hardware is required by the International Building Code (IBC) and NFPA 101 – The Life Safety Code, depending on which code and which edition of the code i...:
What LCN closer is used for double acting door?
Resolution:
The LCN 6030 is a Double Acting (or dual action) closer. Requires a "Cased Open Frame" - that means no stops formed in the frame.:
Information on Cisa brand locks and hardware?
Resolution:
Information for CISA locks, cylinders and hardware is not available in Knowledge Center. For all information, please go to Allegion's CISA home page for all information. :
What are ANSI BHMA hardware grades?
Resolution:
The American National Standards Institute (ANSI) and Builders Hardware Manufacturers Association (BHMA) have developed durability, strength and performance standards for every type of door hardware...:
What is clear opening width?
Resolution:
Clear Opening Width for swinging doors is measured (with the door open 90 degree) from the face of door to stop soffit on strike jamb. &nbs...:
What is the difference between Panic Hardware and Fire Exit Hardware?
Resolution:
The most obvious difference (in the device) is the lack of mechanical dogging on a Fire Rated Device. There are some internal parts that may be different and the method it is secured to the d...:
Is there a template that shows where to drill the hole for E/EL/SS/RX/LX/CX wires?
Resolution:
The hole should be drilled in the field once the end cap is located on the door. It is a 5/8" hole, that is located 5/16" from the end of the mechanism case. See installation instruction of t...:
What is an astragal?
Resolution:
An Astragal is an applied molding attached most commonly to the meeting edge of doors to: Protection against weather conditions Minimize the passage of light between the doors Retard the passa...:
Are GrainTech doors available with hardware preps?
Resolution:
All hardware options (available on standard door) are available on GrainTech® doors. Available hardware are covered in the Steelcraft Price Manual. GrainTech® doors can be prepped for the Von Dupr...:
Where can I find templates for the 237L two point latch device?
Resolution:
Click HERE for the instruction and template for 237L device.:
What firmware does my CO-100 lock have?
Resolution:
CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus. :
What's needed to write a door hardware specification?
Resolution:
The following items are needed for Spec Writers to write a door and hardware specification Building code being used Occupancy type or types Occupancy load for any rooms or areas of ass...:
Where is the template for the 718 trims made after 2/28/2011 for Falcon/Monarch concealed vertical rod devices?
Resolution:
Templates for current 718 series trim can also be found on Falcon website:
What is GrainTech?
Resolution:
GrainTech® is a Steelcraft door option which provides a wood grained pattern which is embossed into both face sheets of the door. GrainTech doors are factory stained and top coated with a cle...:
What is delayed egress hardware?
Resolution:
Delayed egress hardware prevents a door from being opened from the egress side, usually for a period of 15 seconds. This type of device is often used to prevent theft, while maintaining life safe...:
Where are hardware templates?
Resolution:
All the templates can be found at us.allegion.com Please click here :
What templates do I use for the RX98L x E996L?
Resolution:
Click Here to view the Hollow Metal or Wood Door Templates for Von Duprin devices The E996L trim and RX98/99 devices use the standard 996L and 98/99 templa...:
What options are available on the CE-Series doors?
Resolution:
CE Series door in a variety of embossed panel designs and gages. The CE series embossed panel doors also offer a wide range of specifiable options including sizes, and hardware prepar...:
What causes the top rod case to pull away from or strip out of the face of a steel door?
Resolution:
Hardware falling off a door is caused by one or all of the following issues: Field abuse Improper internal reinforcements in the door Improper field preparation The top or bottom rod case can...:
What is a Cam Lift Hinge?
Resolution:
Cam Lift Hinges are specially designed hinges used mainly on acoustical door assemblies. The Cam Lift Hinge lifts the door during its travel and seats the door bottom for a pos...:
Does Allegion write specifications and specs?
Resolution:
Allegion does provides professional support to Architects and Design Professionals. For information related to specification development and support, Website for Architects and Desig...:
Where is the template for the 25C NL-OP?
Resolution:
The NL-OP function for 25-C uses the 718C trim, so template T-2211 for metal doors and W-2211 for wood doors for 718 trims prior to 2/28/2011. T-2211 for trims prior to 2/28/2011 W-2211 for...:
Why are frames grouted?
Resolution:
Grouting frames is: A process done in the field during hollow metal frame installation The internal cavity of the frame is fill with masonry or mortar It is intended to mainly provide ...:
Where can I find LM9300 templates?
Resolution:
No actual templates exist for this hardware. This hardware is currently only available for use on the Steelcraft Paladin series door and frame assembly and is sold as a complete package with the lo...: