Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ What power supply for mag lock ”

RELATED FAQS

Resolution: :

Does the M490DE come with a delayed egress warning sign?

Resolution: A delayed egress sign is provided with the M490DE and the M490DEP. The sign's part number is P774358:

Resolution: The programming processes for Allegion devices can be both product and features specific. Some products programming processes are electronic in nature, others are physical in nature. &nb...:

What power supply do I use with an L9000 electrified L lock?

Resolution: Applies to L9080EL/EU, L9082EL/EU (Discontinued) The Schlage L9080 EU/EL and L9082 EU/EL require 24 VAC/VDC with a peak current of 1.3 Amps at 5 to 10 second intervals and a holding ...:

CM Magnetic Stripe Card Track Options

Resolution: CM locks with a magnetic stripe reader can only be set to read one of the three mag tracks at one time. The CM lock with magnetic stripe reader was shipped from the factory with the magnetic stripe...:

Why does the Schlage button light up “Green” when I open the door?

Resolution: When unlocking the CO200 door by mechanical key override, the green led will be continuously ON until the key is released. This will occur after firmware CO.A.6 (or later) has been installed int...:

Can the AD-Series and CO-Series magnetic card credential readers be set to read data from different magnetic card tracks?

Resolution: Customers will need to use the Schlage Utility Software (SUS) on the HHD lock programming device to set the desired magnetic track to be read for access control, if not using default Track 2&n...:

What is the low battery threshold for the AD and CO Locks?

Resolution: CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...:

What is the SUS feature "Device Template"

Resolution: See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...:

What wire gauge and run is recommended for Von Duprin electric latch retraction EL device?

Resolution: :

What power supply is needed for EL devices?

Resolution: You can use a Von Duprin PS914 power supply with any of the following option boards depending on the application. 900-2RS board will power 1 or 2 devices that do not require timing from pow...:

What is the Buy American Act (BAA)?

Resolution: BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegio...:

How does Cache mode work on AD400 and AD300 locksets?

Resolution: An AD400 granting credentials access in “cache mode” will blink the Schlage with the normal green LED, followed by a brief red Schlage LED flash, indicating no RF communication and access was grant...:

Why is a 5100 electric strike clicking but not locking?

Resolution: Follow the steps below to troubleshoot the problem. Measure the voltage at the electric strike. If the strike is FSE and not locking there should be no voltage at the strike and if it is FS there ...:

Why is the battery draining so quickly on an AD-Series lock with a Keypad ONLY (KP) credential reader?

Resolution: A Technical Note has been generated to document one method of measuring battery current. See the attachment HERE.:

What is the most common practice for running electric power from a frame to the door and hardware?

Resolution: Electrical hinges or a power transfer units are the most commonly used practices to run electric power to locks and/or strikes. Electric Hinges: Most electric hinges will fit into...:

Will mag locks operate with voltage ranges between 12vdc and 24vdc?

Resolution: The entire series of mag locks that Schlage provides advertises 12vdc or 24vdc because they will automatically determine what voltage is being used and switch the internal circuitry based on that v...:

Can we run both mag locks and EL devices from the PS 914?

Resolution: It requires 900-4RL and 900-FA option boards to release the mag locks when a fire alarm is activated. Specify PS914 x 900-4RL x 900-FA.:

Can a Von Duprin delay egress controller DE5101 run a pair of doors?

Resolution: One Delayed Egress Controller (DE5101) can run two mag locks on a pair of doors, provided the doors are not controlled independently:

Does Falcon offer a Delayed Egress exit device?

Resolution: There is not a fully self-contained delayed egress like a Von Duprin Chex-It device but the Falcon RX-24 or RX-25 Series can perform a delayed egress by using the DE5300 controller, power supp...:

Will a PS902 power my mag lock and my DE5101?

Resolution: This is possible as long as the total current draw does not exceed the 2 amp capacity of the PS902 power supply. The Schlage Electronics 320, 350, or 390 maglock must be used with a DE5101 and th...:

What is a locknetics 268/24-10 dual mag functionally equivalent to?

Resolution: Functionally equivalent to a schlage 350+ which is functionally equivalent to a M450:

Why is my mag lock buzzing?

Resolution: Rattling could be caused by improper mounting of the mounting plate or armature. Make sure all components are properly secured.:

Does Von Duprin still sell mag locks?

Resolution: Von Duprin discontinued selling mag locks in the early 1990's.: