Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
Falcon ADA policy
”
RELATED FAQS
Question
Answer
How do you order the L series lock with an ADA thumbturn?
Resolution:
Effective December 9, 2019, Schlage L Series mortise locks with a thumbturn will ship standard with our new ADA thumbturn. The new ADA thumbturn is slightly smaller than the existing design w...:
What is the minimum clear opening width required by ADA on a single door?
Resolution:
The minimum clear opening width for ADA is 32" measured from face of door opened to 90 degrees to face of stop on strike jamb. There must be no hardware mounted to the door projectin...:
Can a 4040 open to 180°?
Resolution:
The 4040/4040XP closer mountings have the following maximum opening degree templating: The 4040/4040XP PA "Regular Arm" mount will allow for 180° max. opening. The 4040/4040...:
Does Schlage or Falcon manufacture a stainless steel cylindrical or mortise lock?
Resolution:
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...:
What template to use for the Falcon MA mortise lock?
Resolution:
The following templates are for the MA lock. Use the matrix in each template for the specific function. See here for Sectional trim . See here for Escutcheon trim. :
How do I set the hold open on my 4040 closer?
Resolution:
The hold open position on a "REG" or "EDA" hold open arm is set with the door to a few degrees shy of the desired hold open point. To properly set, open the door 5° less then the desired hold open...:
What is the function of a T571?
Resolution:
Outside lever is locked or unlocked by key. When locked by key it can only be unlocked by key. Push-button locks outside lever. Turning inside lever or closing door releases button. Inside lever i...:
What is the part number for the lever return spring for the old M series mortise lock?
Resolution:
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series. Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...:
How does a Falcon Hotel cylinder operate?
Resolution:
The following document contains information on Falcon (Non I/C) Hotel Cylinders, including part numbers, key requirements and operation. Falcon Hotel Cylinders.:
How do you identify the model of a Falcon closer?
Resolution:
To determine the SC series, measure center to center on the closer body bolt hole mounting pattern and an overall description of the closer and arm. SC91 -- 6-3/8" x 3/4" -- unique arm SC93 -- 9-1...:
How do I get a Size 1 (ADA) closer to close against air pressure?
Resolution:
If an Size 1 (ADA) closer is set to 5 lbs. opening force, it will only have about 3 lbs. (60/70%) closing force. If the closer will not close against air pressure, but the ADA requirements have to ...:
Are the D100 and D200-Series thumbturns ADA compliant?
Resolution:
The D100-Series and D200-Series have ADA compliant thumbturns. See the sell sheet stating ADA compliance.:
Are Ives pulls ADA compliant?
Resolution:
8103EZ and 9103EZ have 2 1/2" clearance the other pulls have 1-1/2" clearance. Check with your local code for clearance required.:
Do Von Duprin Exit devices meet the 5 pound force requirement for opening an ADA handicapped door opening?
Resolution:
The 5 pound force requirement is in reference to the maximum force to swing the door, not the maximum force allowed to unlatch the exit device. Maximum allowed force to retract the Von D...:
Is there an ADA thumbturn offered in the MA locks?
Resolution:
Falcon does not offer an "ADA style thumbturn.:
Does the 8827 with the 248L-4 strike meet ADA?
Resolution:
The 248L-4 strike will not violate ADA. If you change the 248L-4 to the 304L strike, then the latch would need to be lowered.:
Is the B500 and B600, B700, B800 thumbturn ADA compliant?
Resolution:
The Schlage B500-Series and B600/700/800-Series have ADA compliant turns. See our deadbolt literature under downloads.:
How do I identify the old Falcon T lock chassis versus the new T lock chassis?
Resolution:
The date of manufacture printed on the chassis cover (see below), will determine if you have a revised or old chassis. Chassis manufactured mid-June 2013 will have the new improvements. The first...:
How do I remove an X lock from the door?
Resolution:
To disassemble an X lock, remove the inside knob and unscrew the inside collar and rose. The X lock spanner wrench (012172-000-30) can be used to depress the knob catch as well as tighten/loo...:
How do I identify the old Falcon T lock latch from the new T lock latch?
Resolution:
For T locks shipping mid-June 2013, the new latch can be identified by viewing the deadlatch profile. The profile of the deadlatch has changed from a "full moon" to a "half-moon". See figure below....:
How do I cut a door to accept a Falcon W series lock?
Resolution:
For W lock levers, you can choose whether or not to install the mounting posts. This will also affect how the door is prepped so be sure to determine how you will install the locks befor...:
ADA
Resolution:
Americans with Disabilities Act:
What would cause a Falcon 8200 (8230/8240) operator to slam the door closed?
Resolution:
The Benchmark 9100 series and Falcon 8200 Series operator will allow the door to slam if: The motor is not connected (plugged into) the controller as the closing speed is controlled by a c...:
Warranty information on Allegion Commercial products.
Resolution:
See here for our Warranty Information. :