Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ Are there special templates for Falcon closers ”

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

What special template (ST) is used with a 2030 closer and GJ over head stop?

Resolution: Special template ST-2211 is used to mount a 2030 series closer with a GJ 70,79,81,90, and 450 series overhead stops. This ST works with any GJ "surface" mounted stop. The 2030 closer cannot b...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

What special template (ST) is used with the 2030 closer and a low profile track and roller?

Resolution: The 2030 closer requires a minimum 1-3/8" top rail on the door for the standard track. For a top rail less than 1-3/8" and as narrow as 1", you could use the l...:

What special template (ST) is used with a 4110 closer and GJ90 series?

Resolution: ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:

Can you convert a 4041 Cush arm to a 4041 HCush arm and use the same templating?

Resolution: The 4040XP/4041 Cush and HCush (Hold Open Cush) use the same instructions / template.:

What is the maximum degree of opening you can template a 4110 Cush closer?

Resolution: The 4110 Cush closer can be templated for 85°, 90°, 100°, and 110° maximum as standard templates.The 4110 if ordered by ST-3220 will allow templating to 135°:

Can a 4110 EDA and a Glynn Johnson 100 be used together?

Resolution: A special template is not needed, the closer drops down far enough on the door where it does not conflict with the GJ100 series concealed overhead stop. :

Warranty information on Allegion Commercial products.

Resolution: See here for our Warranty Information. :

How do you adjust a door closer?

Resolution: How to: What are the steps to adjust a door closer? Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All cl...:

What LCN closer is comparable to the Norton 7500?

Resolution: The Falcon SC71 is an exact replacement for the Norton 7500. The LCN 1460 or 4040 Series closers could be used, the mounting hole pattern is different.:

Are the Falcon SC Series door closers fire rated?

Resolution: Yes, the Falcon SC Series closers have a UL listing.:

How do you identify the model of a Falcon closer?

Resolution: To determine the SC series, measure center to center on the closer body bolt hole mounting pattern and an overall description of the closer and arm. SC91 -- 6-3/8" x 3/4" -- unique arm SC93 -- 9-1...:

Which Falcon SC closer is the closest match to a LCN 4040?

Resolution: The Falcon SC 71:

Which Falcon closer has the mounting hole pattern of 12" x 3/4"?

Resolution: The Falcon SC81 series closer has a mounting hole pattern of 12" x 3/4".:

What is the narrowest door a 4040 pull side will mount on?

Resolution: 14" door leaf is the narrowest with standard template.:

Resolution: Special Template:

When did we Von Duprin release the RX996L trim as a standard?

Resolution: The Von Duprin RX996L trim was released to standard order entry in May 2010. The Von Duprin 996L and 996L-BE trims can be ordered with RX switch. The 996L-NL and 996L-DT trims can not have the...:

Can a 4040 regular mount installed on the pull side and a Glynn Johnson 90 be mounted together?

Resolution: The LCN 4041/4040XP and the Glynn Johnson 90 series can be mounted in conjunction with each other without a special template. The 4040 door closer is on the pull side of the door and the GJ 90 is ...:

What is a surface mounted door closer?

Resolution: Surface Mounted door closers are the most durable and common type of door closer. Mounted to the surface of the door or frame Can be configured (through installation or arm type) to meet a...:

What closer can be used with Soss invisible hinges?

Resolution: Using Soss hinges with closers can require special device and preparation locations. If you have questions on specific closer applications, please e-mail your request (including a description ...:

Can I mount an LCN Cush closer with an GJ overhead stop?

Resolution: It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:

What is the mounting difference between a 2010 closer and a 2030 closer?

Resolution: The 2010 and 2030 closer are not the same. The 2010 Series closer uses the (larger) 4010 cylinder which requires a 4" minimum frame tube to mount in. The 2030 uses the (narrow) "Pacer" cylinder...:

Does LCN still make a 4010SE / 4110 SE?

Resolution: The LCN 4010SE / 4110 SE series are obsolete, and on longer available (discontinued around Aug 1995). They were replaced by the 4040SE series.The 4010SE / 4110 SE track is replaced w...:

Can a magnet, or sentronic device, be released and close the door from a button at a desk?

Resolution: If a door is being held open by the LCN SEM 7800/1900 magnet or any ME/SE Series Sentronic LCN closer, you can remotely release that door to close by ordering the following parts and wiri...:

Does a SEH require a door closer?

Resolution: The SEH is an "electronic holder" (ONLY) that is used to hold open a Fire Rated opening. It requires a door closer to be mounted on the opposite side. It is normally used on an existing opening wit...:

What special template (ST) is used with a 4640 operator and a deep reveal?

Resolution: The "Regular Arm" allows for a reveal up to 4-1/2".The "Long Arm" allows for a reveal between 4-1/2"- 8".ST-3088 is a special "Extra Long Rod" used to mount a 4640 operator on an opening ...:

SPECIAL TEMPLATE

Resolution: ST:

What special template (ST) is used with a 4040XP with a non-adjustable (solid) regular arm for pull side mounting?

Resolution: Special Template ST-2795 is used to mount a non-adjustable (solid) regular arm for pull side mounting. :

Where is the template for the 718 trims made after 2/28/2011 for Falcon/Monarch concealed vertical rod devices?

Resolution: Templates for current 718 series trim can also be found on Falcon website:

On which closer is the fusible link arm available?

Resolution: The Fusible Link arm is available with the 4010, 4020 and 4110 series closers. They all use the same Fusible Link arm. The UL Listing number is for the Fusible Link arms is R1943.The 4010 Series ca...:

What are Overhead Concealed door closer?

Resolution: Overhead Concealed door closers are used to provide a more aesthetic look to the opening. Concealed in either the frame or the door Offer the ability to be adjusted to maintain...:

Is dogging available w/ EL option on 24 or 25 series devices?

Resolution: This option is not available as the solenoid is in the mechanism case where the dogging components would go. An HD-EL solenoid is not available, and Special Dogging(SD) is not an optio...:

What options are available to add frame reinforcement for surface closer?

Resolution: Steelcraft offers two optional types of reinforcements for open section header to be installed in distributor shop or in the field: Full profile sleeve; is a 14 gauge, 16" long part to fit the p...:

When did the 4111 Cush arms become non-handed?

Resolution: This engineering change did affect the templating of the closer. The stop in the shoe is slightly larger than the original handed cush shoe. The new non-handed arm template locates the closer and s...:

Can you install a 4041 pull side at 180 degrees?

Resolution: The maximum opening is 120° with the 4041/4041XP standard templating on the pull side of the door.For pull side mount, you can achieve 160° of door opening with ST-2359, which consists of...:

SPCL

Resolution: Special, Prep per template; Not standard:

What LCN closer is used for double acting door?

Resolution: The LCN 6030 is a Double Acting (or dual action) closer. Requires a "Cased Open Frame" - that means no stops formed in the frame.:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ Are there special templates for Falcon closers ”

RELATED FAQS