Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
AD replace reader module
”
RELATED FAQS
Question
Answer
What is the low battery threshold for the AD and CO Locks?
Resolution:
CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...:
Can the credential reader be changed on a CO-Series lockset?
Resolution:
A Credential Reader MAY be replaced with another Credential Reader of the same type; however, a Factory Default Reset must be performed before the lock will function properly.:
What process should be followed to change the Credential Reader type on a AD-Series lock?
Resolution:
The process to change the Credential Reader on an AD-Series lock is as follows: Note: To ensure firmware compatibility of the lock and reader, it is important that the firmware in the LOCK and the...:
When should I update the firmware in my AD Series or CO Series products?
Resolution:
Steps to determine what firmware version your products are currently using AND if a firmware update is suggested: 1) Use the Hand Held Device (HHD) and Schlage Utility Software (SUS) applicat...:
How can a TK400 be reset to factory defaults
Resolution:
If a factory default reset (FDR) is absolutely needed, you MUST temporarily replace the credential reader with another reader that has a Schlage Button. This should be rarely if ever required. T...:
What is the "HOST BITS" setting on a Hand Reader with an Ethernet Module?
Resolution:
Handreaders require a static (fixed) IP address; this means you have to set its IP address, subnet mask and default gateway.These are usually assigned or issued by your local network administrator....:
Why did my CO Lock stop working after the Reader Module (electronics) was changed?
Resolution:
CO Reader Modules are not individually replaceable, nor can they be swapped between locks. The inside and outside assemblies of a CO lock are a matched/mated set and cannot be swapped to change rea...:
The plug on my CIP Module is broken
Resolution:
The miniature banana plug on the module can be ordered directly from the part manufacture (Pomona Electronics, Sales: 900-490-2361 part number model #4513) or from (Digi-Key part number 501-1425-ND).:
What Proximity technologies do XceedID readers support?
Resolution:
ISOX card technology is no longer supported - contact XceedID sales:
Why is the battery draining so quickly on an AD-Series lock with a Keypad ONLY (KP) credential reader?
Resolution:
A Technical Note has been generated to document one method of measuring battery current. See the attachment HERE.:
Can the AD-Series and CO-Series magnetic card credential readers be set to read data from different magnetic card tracks?
Resolution:
Customers will need to use the Schlage Utility Software (SUS) on the HHD lock programming device to set the desired magnetic track to be read for access control, if not using default Track 2&n...:
What card types and formats will our AD and CO smart readers support?
Resolution:
See attachment for details: Smart readers support::
Is the FMK reader FIPS 201 compliant?
Resolution:
The FMK reader on an AD Series lock is capable of reading PIV and PIV-I credentials, however, alone it no longer complies with the new FIPS 201-2 standard in which the lock with reader (AD-302 and ...:
What card types and formats will our AD and CO proximity readers support?
Resolution:
See attachment for details: Proximity readers support:
What card formats will our AD and CO magnetic swipe readers support?
Resolution:
See attachment for details: Magnetic Swipe reader supports::
Why does my AD-200 not accept a new programming code?
Resolution:
Early versions (12/09 ) of the AD200 User Guide in many DEMO kits incorrectly state the Programming sequence to change the a programming code. It shows entering the new programming code o...:
What drains the AA batteries on an AD-Series lock?
Resolution:
Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1) One the four (or eight) AA was inserted reversed and the rese...:
How does Dynamic Channel Switching (DCS) work on the AD-Series?
Resolution:
Setting Dynamic Channel Switching 1) Connect and couple the SUS to the PIM400 you intend to change. See the SUS User Guide for details 2) Under “PIM Properties” and the “Edit” tab is ...:
How do I change an AD-Series lock to a different AD-Series lock type?
Resolution:
Re-classing is the process by which an AD-Series device is able to change its lock type. The AD-Series has a modular architecture and a major benefit of this type of architecture is that it allows ...:
Can I change an AD lock from an 8 "AA" battery pack to a 4 "AA" battery pack?
Resolution:
The AD lock battery pack type can be changed following this procedure:1. Disconnect the existing battery pack2. Depress and hold the SCHLAGE button for a few seconds to drain off any residual...:
AD changing Function in the field
Resolution:
-On the AD series offline locks only you can change the lock function from Classroom/Storeroom to a Privacy, office or apartment function out in the field. - This is done via the HHD/SUS using...:
Can a CO200 reader be placed on a CO250?
Resolution:
A CO200 reader will not work on a CO250 lockset and a CO250 reader will not work on a CO200 lockset.: