Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ why is cush arm parallel ”

Resolution: Cam Lift hinges can only be used with LCN door closers that have a "Regular" or "Reg hold Open" style arm. Locating the Closer and Arm from the centerline of the pivot point of the cam lift h...:

What is the part # for the 4040 HCush arm?

Resolution: The part number for the 4041/4040XP HCush arm is 4040XP-3049CNS.:

What are the 1460 closer arm options?

Resolution: The 1460 Regular Arm part numbers are: Regular Arm -- 1460-3077 or 1460-3077L for long arm (must specify finish). Regular Arm with PA -- 1460-3077PA (must specify finish). Regular Hold Open Ar...:

When did the 4111 Cush arms become non-handed?

Resolution: This engineering change did affect the templating of the closer. The stop in the shoe is slightly larger than the original handed cush shoe. The new non-handed arm template locates the closer and s...:

Is the EDA or Cush arm with threaded studs still available?

Resolution: ST-3195 is used to obtain the old style EDA or Cush arms which were assembled with threaded studs so that you could take apart the arm assemblies. Our current standard EDA and Cush arms are rivet...:

How do you order a 4110 hold open spring cush arm only?

Resolution: The 4110 hold open spring Cush (Spring H Cush) arm part number is 4110-3049SCNS.:

Can you convert a 4041 Cush arm to a 4041 HCush arm and use the same templating?

Resolution: The 4040XP/4041 Cush and HCush (Hold Open Cush) use the same instructions / template.:

SPRING HOLD-OPEN CUSH ARM

Resolution: SHCUSH,:

What are Pneumatic Automatic Operators?

Resolution: Pneumatic Automatic Operators are used in areas where electrically operated devices are not convenient or permitted. Consists of a modified, heavy-duty door closer for manual oper...:

How can I make my regular arm closer mount parallel arm?

Resolution: This can only be done with universal, non-handed closers: 1250, 1260, 1450, 1460, 4030, 4040XP, and 4050A.You would need an xxxx-62PA shoe to adapt from regular arm to parallel arm mount...:

How do you adjust a door closer?

Resolution: How to: What are the steps to adjust a door closer? Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All closers with a "Del...:

How do I set the hold open on my 4040 closer?

Resolution: The hold open position on a "REG" or "EDA" hold open arm is set with the door to a few degrees shy of the desired hold open point. To properly set, open the door 5° less then the desired hold open...:

Can I mount an LCN Cush closer with an GJ overhead stop?

Resolution: It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:

What is the part number for the Spring Cush block?

Resolution: The part number for the Spring Cush block assembly is: model number-3080. EXAMPLE: 4110-3080:

Does the old style 4030 have the same templating as the new style 4031?

Resolution: The old 4030 series was: Handed Mounted regular arm hinge side. Had sized springs, were not adjustable. The 4033 is an obsolete closer. If required, handing can be verified by looking at ...:

What is the difference between an LCN CUSH arm, and an LCN EDA arm?

Resolution: EDA ARM - The EDA arm is a heavy duty parallel arm mount. The degree of door opening is determined by the template used for mounting. EDA arm closers can only be mounted as a Push S...:

Can you mount a 4041 Cush arm with a EDA arm template and get 180 degrees opening?

Resolution: The dead stop post would need to be removed and the 4040/4040XP EDA mounting template for 180° would be followed.:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ why is cush arm parallel ”

RELATED FAQS