Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ WHERE CAN I FIND SPECIAL TEMPLATES FOR CLOSERS? ”

RELATED FAQS

Resolution: All the templates can be found at us.allegion.com Please click here :

Can a 4040 Pull Side closer be mounted with Swing Clear Hinges?

Resolution: ST-1583 is used to template a 4040 or 4040XP closer mounted hinge side with swing clear hinges. This ST is templating only – it uses standard parts.For current ST add on pricing ...:

What special template (ST) is used with a 2030 closer and GJ over head stop?

Resolution: Special template ST-2211 is used to mount a 2030 series closer with a GJ 70,79,81,90, and 450 series overhead stops. This ST works with any GJ "surface" mounted stop. The 2030 closer cannot b...:

What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

What special template (ST) is used with a 4110 closer and GJ90 series?

Resolution: ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:

What special template (ST) is used with the 2030 closer and a low profile track and roller?

Resolution: The 2030 closer requires a minimum 1-3/8" top rail on the door for the standard track. For a top rail less than 1-3/8" and as narrow as 1", you could use the l...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

Can you convert a 4041 Cush arm to a 4041 HCush arm and use the same templating?

Resolution: The 4040XP/4041 Cush and HCush (Hold Open Cush) use the same instructions / template.:

What is the maximum degree of opening you can template a 4110 Cush closer?

Resolution: The 4110 Cush closer can be templated for 85°, 90°, 100°, and 110° maximum as standard templates.The 4110 if ordered by ST-3220 will allow templating to 135°:

Can a 4110 EDA and a Glynn Johnson 100 be used together?

Resolution: A special template is not needed, the closer drops down far enough on the door where it does not conflict with the GJ100 series concealed overhead stop. :

Can I mount an LCN Cush closer with an GJ overhead stop?

Resolution: It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:

Does a SEH require a door closer?

Resolution: The SEH is an "electronic holder" (ONLY) that is used to hold open a Fire Rated opening. It requires a door closer to be mounted on the opposite side. It is normally used on an existing opening wit...:

What is the mounting difference between a 2010 closer and a 2030 closer?

Resolution: The 2010 and 2030 closer are not the same. The 2010 Series closer uses the (larger) 4010 cylinder which requires a 4" minimum frame tube to mount in. The 2030 uses the (narrow) "Pacer" cylinder...:

Can a magnet, or sentronic device, be released and close the door from a button at a desk?

Resolution: If a door is being held open by the LCN SEM 7800/1900 magnet or any ME/SE Series Sentronic LCN closer, you can remotely release that door to close by ordering the following parts and wiri...: