Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ what is PA-AX ”

RELATED FAQS

Resolution: The 4040/4040XP closer mountings have the following maximum opening degree templating: The 4040/4040XP PA "Regular Arm" mount will allow for 180° max. opening. The 4040/4040...:

What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

What is the replacement for an LCN 1070?

Resolution: The P1070 was replaced with the 1261 Rw/PA.The 1260 arm can be used as a replacement arm for the discontinued 1070.The P1070 arm can be used on a replacement 1260 body to maintain the origina...:

Where is the RA closer reinforcement located on a frame for a Regular Arm Closer?

Resolution: Optional closer reinforcements are located at 3" from hinge jamb to the beginning of the reinforcement plate. This applies to Regular Arm, Parallel Arm, Top Jamb. Regular Arm (RA) closer reinfor...:

What is the difference between a regular arm and the Rw/PA arm?

Resolution: The Rw/PA arm is simply a regular arm that is packed with a 62PA (parallel arm) shoe, which will allow a (Tri-Pack) closer to be mounted in a regular, top jamb, or parallel arm application.:

What is a 62A shoe used for?

Resolution: The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc.:

What drop plate is used with a 4040 Rw/PA?

Resolution: The 4040 Rw/PA can be mounted 3 different ways. The 4040-18 drop plate is used for the regular pull side mount. The 4040-18TJ drop plate is used for the top jamb push side mount. The 4040-18P...:

What do I need to do to make my 4041 Reg/PA a hold open arm?

Resolution: When placing an order for a 4041/4040XP Rw/PA with hold open, it would be ordered as a 4041 /4040XP Hw/PA. For an existing Rw/PA requiring the addition of a hold open function, a hold open arm woul...:

How much top rail is needed on a 4041 REG/PA (Rw/PA)?

Resolution: To install a 4041/4040XP with Rw/PA or Hw/PA arm, you need a minimum of 5-3/8" top rail on the door, measured from the bottom of the stop. If the top rail is less than 5-3/8", you will need to use ...:

What is the minimum top rail required on a door for 1461 Rw/PA?

Resolution: The 1461 Rw/PA requires a 4-3/8" minimum top rail on the door without the use of a drop plate. If top rail is less than 4-3/8" a 1460-18PA drop plate will have to be used.:

Will a 4040 Hw/PA hold open at 180°?

Resolution: The 4041 Rw/PA and the Hw/PA have the same template. The only difference is the arm. The 4041/4040XP Hw/PA, if mounted to the 180° template, will hold the door open at 180°. Rw/PA is Regular A...:

Do Von Duprin Exit devices meet the 5 pound force requirement for opening an ADA handicapped door opening?

Resolution: The 5 pound force requirement is in reference to the maximum force to swing the door, not the maximum force allowed to unlatch the exit device. Maximum allowed force to retract the Von D...:

HW/PA

Resolution: Hold Open Arm with Parallel Arm Shoe:

What options are available to add frame reinforcement for surface closer?

Resolution: Steelcraft offers two optional types of reinforcements for open section header to be installed in distributor shop or in the field: Full profile sleeve; is a 14 gauge, 16" long part to fit the p...:

RW/PA

Resolution: Regular Arm with Parallel Arm Shoe:

What LCN closers are available in a tri-pack mounting?

Resolution: The 4040XP, 1260/1261, 1460/1461, 4030/4031 closers have the tri-pack mounting option when ordered with an Rw/PA or Hw/PA designation.:

Resolution: Parallel Arm:

What can I use instead of the EDA with 145 shoe?

Resolution: The 419 panel adaptor is the replacement for both the obsolete 145 shoe, and 418 panel bracket (both were made obsolete in 2009). The 419 panel adaptor is 4" wide, 2" tall, and projects 3". ST-069...:

PA SHOE ADAPTER

Resolution: Narrow Frame, PA Mount, Parallel Arm Mount, Parallel Arm Installation, PA Installation:

What are the 1460 closer arm options?

Resolution: The 1460 Regular Arm part numbers are: Regular Arm -- 1460-3077 or 1460-3077L for long arm (must specify finish). Regular Arm with PA -- 1460-3077PA (must specify finish). Regular Hold Open Ar...:

PA SHOE

Resolution: PA Mounting, Parallel Arm Mounting: