Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ What is door weight ”

RELATED FAQS

Resolution: All Steelcraft doors are a nominal 1 3/4" thick. Special door thicknesses are not available.:

What are the minimum stile and rail dimensions for the L-Series door FG, FG2 & FG3?

Resolution: The minimum stile and rail dimensions are to exposed glass are: Stiles = 6 13/16" Top Rails = 6 3/4" Center Rails = 7 1/2" Bottom Rail = 10 3/4" For high traffic and high abuse locations th...:

What is exposed glass size?

Resolution: When dealing with glass lights in doors, there are three (3) critical dimensions which must be coordinated: Exposed Glass Size (EGS) - the horizontal and/or vertical dimensional size of the vision...:

What is the minimum dimension from the edge of the door to a glass light cutout?

Resolution: Minimum dimensions to cutouts for glass lights: Vertical edge of door to edge of cutout = 5 29/32" Top of door to top of cutout = 6" Bottom of door to bottom of cutout = 10" Reinforcing chann...:

What is the max rating available on an full glass (FG) door?

Resolution: A UL 20 minute fire rating is the maximum fire rating for a Full Glass (FG) door design. A14-Series door construction: Max fire rating is 20 minute. UL label only FG must use Over-Lapping Stee...:

What are the dimensions for mounting a 1261 on the pull side of the door

Resolution: http://lcnclosers.com/pdfs:

What are the dimensions of the SC70 footprint

Resolution: The measurements from center line to centerline of the mounting holes are 2-3/8" x 6-3/4".:

Where is the wood template for the 996L-DT ?

Resolution: There is no template for 996L-DT for wood door. You will need to use the 996L-DT installation instruction or 996L-DT metal template. See attached instruction/template 996L-DT instruction/template.:

What is the standard screw size used on Steelcraft doors with 4 1/2" or 5" hinges?

Resolution: Steelcraft follows the industry standards for hinge reinforcement and preparation for both door and frame. Unless otherwise specified all products prepared for butt hinges will have mounting holes ...:

What is the Falcon SZ-Series Door?

Resolution: Falcon SZ Series Door is the economy Steelcraft commercial grade door recommended light commercial applications when architectural specification are not needed. Options: The SZ-Series door is...:

What is maximum width, height and weight for IVES butt hinges?

Resolution: Butt hinges can be used on doors up to 4' wide and 200 pounds. There is no maximum door height. However, an additional hinge must be installed every 30" when exceeding a 7' d...:

What is a 320G door closer?

Resolution: The "320G" is the # on a UL sticker attached to the arm of most LCN door closers, and is not a door closer model number. The "320G" means that the arm is not a mechanical hold open device and OK t...:

What is the maximum door weight recommended for LCN closers?

Resolution: The maximum recommended door weight for LCN manual closers is 225 lbs.:

Are glass lights available in the H-Series door?

Resolution: Steelcraft offers all the standard lights as well as special size glass lights in the H-series door. Effective April 1, 2012, (Bulletin # B-100.12) the default for Dezigner Trim in H-Series D...:

Can a door have an INPACT device and glass lights?

Resolution: Glass lights available:Standard Glass Lights - The N4, N5 & V lite can be used at standard locations without any modification.Glass Light Options - Other glass lights are available but have lim...:

RU strike identification for early Corbin Russwin applications.

Resolution: The RU lock can be requested as a retrofit for early Corbin Russwin Unit locks. Several types of strikes are offered depending on the strike conditions but two are very similar with the e...: