Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ von duprin break-away ”

RELATED FAQS

Question
Answer
What is the break-away point for the Schlage SL1 ligature resistant trim?
The Schlage SL1 ligature resistant lever is designed to break-away between 100 and 200 inch-pounds.  The lever will rotate at this point but not allow access.
What would cause an EL device to pull and release?
If your Von Duprin EL (solenoid) device pulls and releases quickly instead of holding the latch retracted, please check all of the items below.In most cases, one or more of these solutions will r...
What is Vandlgard?
The Schlage Vandlgard option available on select L-Series (LV9000) and ND-Series is ideal for areas subject to abuse or anywhere vandalism is likely to be present, such as schools, universitie...
Vandlgard is specified by "LV" for mortise locks.Vandlgard is specified by ND9x functions for ND cylindrical locks.
What is needed to keep the EL device retracted all day?
To keep the Von Duprin electric latch retraction EL or QELA exit device dogged (retracted) all day, have your access control, Key pad, key switch, fire alarm contact or any other signals ...
What gauge wire is needed for a CX device?
For devices shipped after 8-24-2015 with motor driven:  a.       0-200 ft, use  #18 gauge wire b.      0-500 ft, use #14 gauge wir...
For Product Shipped prior to 8-24-2015 with solenoid driven:          a.       0-100 ft, use #14 Gauge Wire      b.&n...
How does the latch bolt retract on the Von Duprin XP device?
The latch bolt on an XP98/99 exit device does not retract. The latch bolt will release and pivot out of the way when push bar is depressed or out side trim is activated.
Can the fire label be replaced on a Von Duprin device?
The UL fire label is only applied to the device center case cover at the factory when the device is built.  This label can not be sold or replaced with a new one.
What is the finish warranty on Allegion products?
Finish is not specifically stated as being covered under warranty as it is covered under defects in material and workmanship.  EXCEPTION: There is no finish warranty for Falcon products. ...
Falcon lock warranty statementIves warranty statementGlynn-Johnson warranty statementLCN closer warranty statementSchlage warranty statementSteelcraft warranty statementVon Duprin warranty statement
When were 313AN & 315AN anodized finishes changed to SP313 (695) and 622 powder coat finishes?
Beginning December 6, 2010, all 33A, 35A, 98 & 99 devices ordered as 313AN Anodized was furnished in SP313 (dark brown powder coat).  All devices ordered as 315AN wil...
What is the part number for the end cap and bracket for the 22 device?
End cap without end cap bracket is 968601. End cap kit with bracket is 900981 End cap bracket is 971795-89
Hardware finish warranty
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechP...
Is there a Von Duprin conversion kit to change mechanical to electric latch retraction EL in the field?
Followings are the list of the electric latch retraction EL/HDEL (hex dogging), QEL (quiet) kits: 114317-00 QELA Mod. Conv. Kit 040061-00 QELA Mod. Conv. Kit...
What wire gauge and run is recommended for Von Duprin electric latch retraction EL device?
  For Product Shipped Prior to August 2012 using the old (black) potted module: a.       0-100 ft 14 gauge wire b.      0-200 ft 12...
 
Why doesn't full rotation of the AD or CO Series Exit Trim (993) outside lever fully retract the Von Duprin 98/99 Exit Device latch?
- AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device.  Be sure this screw is installed- Exit hardware and strike must be properly mounted ...