Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ special template offset pivots ”

RELATED FAQS

Resolution: The SEH is an "electronic holder" (ONLY) that is used to hold open a Fire Rated opening. It requires a door closer to be mounted on the opposite side. It is normally used on an existing opening wit...:

Where can I find discontinued G lock templates?

Resolution: Schlage G Series template locate here. :

What special template (ST) is used with a 2030 closer and GJ over head stop?

Resolution: Special template ST-2211 is used to mount a 2030 series closer with a GJ 70,79,81,90, and 450 series overhead stops. This ST works with any GJ "surface" mounted stop. The 2030 closer cannot b...:

Can DE-Series frames be prepared for pocket pivot hinges?

Resolution: Pocket pivot hinges are mainly used in cross corridor applications where clear opening width is a factor. For frames, pocket pivot hinges are a special hinge options which must be spe...:

Can a 4600 operator be mounted with pivots?

Resolution: On a single door take the mounting dimensions from centerline of pivots (offset or center) On a pair of doors, depending on the door width and pivots being used, the operators can bu...:

Can I mount an LCN Cush closer with an GJ overhead stop?

Resolution: It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:

Can a magnet, or sentronic device, be released and close the door from a button at a desk?

Resolution: If a door is being held open by the LCN SEM 7800/1900 magnet or any ME/SE Series Sentronic LCN closer, you can remotely release that door to close by ordering the following parts and wiri...:

Is there a replacement for the old LCN 4010SE or the 4110SE?

Resolution: The LCN 4010SE / 4110 SE series are obsolete, and on longer available (discontinued around Aug 1995). They were replaced by the 4040SE series.The 4010SE / 4110 SE track is replaced w...:

Do I need to order the LCN 4040XP closer X ST-3596 to get the cover screw to secure the snap on cover to the cylinder?

Resolution: As of June 27th, 2018--- the cover screw is now standard in the screw packs for the 4040XP, 4040XPT, 4000T, and 4040SE so ST-3596 is no longer needed. :

SPECIAL TEMPLATE

Resolution: ST:

What is the mounting difference between a 2010 closer and a 2030 closer?

Resolution: The 2010 and 2030 closer are not the same. The 2010 Series closer uses the (larger) 4010 cylinder which requires a 4" minimum frame tube to mount in. The 2030 uses the (narrow) "Pacer" cylinder...:

What special template (ST) is used with a 4040XP with a non-adjustable (solid) regular arm for pull side mounting?

Resolution: Special Template ST-2795 is used to mount a non-adjustable (solid) regular arm for pull side mounting. :

Can a 4110 EDA and a Glynn Johnson 100 be used together?

Resolution: A special template is not needed, the closer drops down far enough on the door where it does not conflict with the GJ100 series concealed overhead stop. :

What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

Where are hardware templates?

Resolution: All the templates can be found at us.allegion.com Please click here :

Will a Senior Swing or Swing IQ work with swing clear hinges?

Resolution: Push Side Surface Mount Senior Swing or Swing IQ can be used with swing clear hinges, standard butt hinge/offset pivot templating. Pull Side Surface Mount Senior Swing&nb...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

How do you order a Senior Swing header for a 2810 on one leaf and a 2010 on the other?

Resolution: LCN does offer a 2810 Senior Swing / 2010 manual closer combo for a pair of doors. Both units contained within the same Senior Swing header. To order a paired operator with a 2810 o...:

What special template (ST) is used with the 2030 closer and a low profile track and roller?

Resolution: The 2030 closer requires a minimum 1-3/8" top rail on the door for the standard track. For a top rail less than 1-3/8" and as narrow as 1", you could use the l...:

Can a 450 overhead be used on a 48" wide door hung with butt hinges or offset pivots?

Resolution: The 455 can be mounted on a 48" wide door, but we cannot guarantee that it will withstand the forces involved. Recommend using 906 instead.:

What are the minimum header lengths for a Senior Swing?

Resolution: The minimum header lengths for a Senior Swing with standard Spindle centers are:Concealed 2810 Series:2811 single door (offset pivot or butt hinge) -- 33".2811 single door with stop (cent...:

What special template (ST) is used with a 4110 closer and GJ90 series?

Resolution: ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:

What mounting options are available with the 2030 Series closer?

Resolution: The 2030 Instructions included with the unit has templates for mounting with standard butt hinges, center pivots, and offset pivots.:

What LCN closer is used for double acting door?

Resolution: The LCN 6030 is a Double Acting (or dual action) closer. Requires a "Cased Open Frame" - that means no stops formed in the frame.:

What is the new number for the discontinued LCN CP150 center hung pivot?

Resolution: The 7253 is the Ives pivot set that replaced the LCN CP150. :

What special template (ST) is used with a 4640 operator and a deep reveal?

Resolution: The "Regular Arm" allows for a reveal up to 4-1/2".The "Long Arm" allows for a reveal between 4-1/2"- 8".ST-3088 is a special "Extra Long Rod" used to mount a 4640 operator on an opening ...: