Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ Schlage cylinder in falcon exit device ”

RELATED FAQS

Question
Answer
What is the part number for the Schlage cylinder to work in a Falcon T lock?
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks.  Table 1 below contains part number for T series locks.  Table 1 - Falcon retrofit cylinders  
What non IC cam is offered by Schlage to work in a Falcon MA lock?
Schlage now offers modular style cams to operate the Falcon MA locks.  The following part numbers are cams for all MA locks (except the MA381): L583-638 for 1-1/8", 1-3/8", 1-5/8" length cylin...
Price Book 72A List Price $8.10
Will a Falcon cylinder work in a Schlage lock?
Key in lever Falcon cylinders do not work in Schlage locks.  The cylinders may fit, but there are no specific tailpieces created to operate any Schlage lock. SFIC SFIC is universal so Falcon and...
   Hotel cylinder in L9000 As long as the correct cam is used (Schlage clover), a Falcon Hotel cylinder will properly function in an L9486 hotel lock.
What cylinder is needed with Von Duprin exit alarm ALK?
The ALK uses a 1 1/4" mortise cylinder with straight cam. (NO DOGGING)
Is the Double Cylinder option available on Von Duprin vertical rod models of the 98/99 series exit device?
Double cylinders are only available on Von Duprin 98/99 Rim and 98/9975 Mortise devices.
Do the Falcon exit devices have the double cylinder option?
A double cylinder(-2) option is not available on a Falcon device but is available from Von Duprin.
What cylinder is used in the Falcon 24/25 exit alarm kit?
The Exit Alarm takes a 1 1/8" Mortise cylinder with a straight cam. See first page of Exit Alarm inst below. Exit Alarm inst
Can I use CD and ALK on a 98/99 series Von Duprin?
Standard 98/99 exit alarm ALK devices are available with cylinder dogging option as of October, 2011. The device can be ordered standard with cylinder dogging and exit alarm ALK opti...
Can I put a Schlage Key-In-Lever cylinder into a Falcon D100 or D200 lock?
Falcon D series deadbolts will not accept Schlage Key-in-lever cylinders. The faceplate plug hole is smaller in diameter than the Schlage plug and does not fit flush when i...
For a Schlage "C"  keyway:  Specify "CP6" as the cylinder suffix when ordering  D100 or D200 locks (All other Schlage keyways are not available).
What is the part number for the Schlage thumbturn rim cylinder?
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...
Can the CD cylinder dogging and RX switch be ordered with 33/35 or 98/99 exit device?
Cylinder dogging (CD) and an RX switch can be ordered together with 33/35 or 98/99 series.
This can be done ONLY with non fire rated exit devices.
What cylinder is used in a 210K trim for the 22 series exit device?
Equivalent to the Schlage D series line with a C keyway. Part number 21-002.
Does the cylinder cam get inverted on the SD option for the Von Duprin 99 exit device?
 A 1 1/4" cylinder with straight cam is required for the Von Duprin SD (Special Dogging) exit device option.
The cylinder cam must be inverted with the SD option to work properly.
What is the finish warranty on Allegion products?
Finish is not specifically stated as being covered under warranty as it is covered under defects in material and workmanship.  EXCEPTION: There is no finish warranty for Falcon products. ...
Falcon lock warranty statementIves warranty statementGlynn-Johnson warranty statementLCN closer warranty statementSchlage warranty statementSteelcraft warranty statementVon Duprin warranty statement
Hardware finish warranty
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechP...