Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ QEL scheduled locking ”

RELATED FAQS

Resolution: When trying to program a CM lock, it may display an error code with a solid green light and 10 read flashes. This indicates the lock has already been programmed with computer software and manual ...:

How is a CM lock manually programmed?

Resolution: In order to manually program a CM lock, there must be a keypad on the reader. If there is not keypad on the reader, then the CM lock can't be manually programmed. Refer to the Schlage 1000 user pro...:

Will the PS900-2 RS operate the Von Duprin QEL device?

Resolution: See below for QEL device requirements: QEL devices shipped prior to 7/23/12 must have the 2Q option board for the communication link between the power supply and the exit device. &nb...:

How much amperage does the QEL draw?

Resolution: Applies only to Von Duprin QEL exit devices shipped after December 11th, 2014.1.0 amp inrush and a 0.14 amp holding current.:

What power supply do I need for my 2 QELA devices with LCN auto operator?

Resolution: Use the PS902-2RS power supply with LCN auto operator on single door, PS904-2RS power supply on double door and PS904/906-2RS-2RS for 2 pair of QELA is required for basic operation with a...:

Why would QEL retract and release repeatedly?

Resolution: The following could cause the QEL device to retract and release repeatedly: If this is a vertical rod type device, the vertical rods could be adjusted too short. Check rods for dead locking, ...:

Will the 900-2Q option board operate an EL device?

Resolution: The 900-2RS is recommended to be used with EL devices but if you have a 900-2Q with PS914 power supply it can be used to operate up to two EL or one EL and one QEL devices .:

What is needed to keep the EL device retracted all day?

Resolution: To keep the Von Duprin electric latch retraction EL or QELA exit device dogged (retracted) all day, have your access control, Key pad, key switch, fire alarm contact or any other signals ...:

Chexit goes into alarm with fast flashing LED and not locking after rearm time.

Resolution: Chexit devices shipped prior to 8-24-2015 with solenoid driven: Chexit device has a RX switch with a connector that needs to be connected to the Chexit module otherwise the alarm will sound af...:

Why is my QEL device not retracting completely?

Resolution: You may have a defective motor bracket, defective base plate or vertical rod could be out of adjustment.:

How far down can an exit device be cut down in the field?

Resolution: For most exit devices, please refer to the specific device series catalog for minimum door opening width the device can be cut down to fit. Be aware that some device options, frame...:

Why is my latch not retracting when I depress the push pad on an XP98/99 device?

Resolution: Pushing on the push bar or activating the EL/QEL or the trim on Von Duprin XP98/99 exit device does not retract the latch, it releases the latch only. Door must be pushed or pulled when device o...:

What are the Von Duprin part numbers for RX, LX and RX,LX-LC switch kits for field installation?

Resolution: The attached table shows the part numbers for LX-RX and LX-RX-LC switches field installed.:

Is the 871-2Q board required on QEL devices when using the PS 873 AO to operate my QEL devices?

Resolution: The QEL exit devices that were shipped prior to August, 2012 will only communicate to the PS873 with 871-2Q option board or PS900 series with 900-2Q option board. If you...:

What is (SD) Special Dogging?

Resolution: SD is Special cylinder dogging in the center case of 98/99 rim and vertical rod non fire rated devices and is available with standard, EL, QEL, CX and ALK.:

Will there be 900-2Q boards for warranty purposes now that the QEL'S do not require the boards?

Resolution: The 900-2Q board is no longer available. For warranty purposes, QEL conversion kit and 900-2RS board are required. The 900-2RS replaces the 900-2Q board. :

Is the SD option available with Von Duprin QEL 98/99 exit devices?

Resolution: SD option is available and is also standard with Von Duprin 98/99 rim and vertical rod exit devices but not available with mortise device.:

Will the QEL+ still work with the 900-2Q?

Resolution: You can use the QEL+ device with 900-2Q option board. The 900-2Q board is obsolete with no stock remaining. :

Is there a conversion kit to make 94/95 devices into a QEL?

Resolution: Yes. Required Series 94 or 95 Fire or Panic 3FT/4FT or 2 ft 6 in / 2 ft 10 in Finish Optional LX switch &nbs...:

Can QEL and RX be added to an existing 9927?

Resolution: The QEL conversion kit (3' or 4') and the RX switch kit (050251-00) can convert the 9927 to QEL-RX9927 device.:

Does the QEL retract the latch bolt and the pushpad?

Resolution: Yes the Von Duprin QEL exit device retracts the latch bolt and pushpad. Pushpad and latch bolt stay retracted as long as power is applied to the QEL exit device. :

Can Von Duprin QEL/EL and CX be in the same device?

Resolution: You can not use these options together on the same device per the following reasons: QEL/EL device retracts the latch bolt of the exit device allowing entry. CX (Chexit) device ...:

Is the EL wiring adapter needed for QEL?

Resolution: The EL wiring adapter is not needed for QEL devices.: