Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
ND backset extension
”
RELATED FAQS
Question
Answer
Can a Von Duprin 3' pushpad exit device be converted to a 4' device in the field?
Resolution:
A 3' exit device cannot be converted to a 4' exit device. You will need to replace the 3' device with a 4'. Conversely, a 4' device cannot be converted to a 3' device. Converting these exit de...:
Does wall board have to extend into the throat of a fire rated frame?
Resolution:
:
What would cause the Von Duprin 88 series exit device latchbolt not to extend and the crossbar to droop?
Resolution:
The spring in the hinge case or end case assembly lifts the crossbar and both lever arms. If broken, the crossbar and lever arms will drop down. The weight of the crossbar and levers will automati...:
How do I attach extensions to my magnet?
Resolution:
The magnet extensions can be used with both the SEM 7800 and the SEM1900 magnets. To add extensions to the SEM series magnets, you "MUST" start with the 7810-514 coupler kit. The coupler kit pro...:
Can I order a "one piece" top rod for an 8827 for a 9' door?
Resolution:
8827 vertical rod device is available for 7 or 8 feet tall door standard. 12", 24", 36" and 48" extension rod kits are available for taller doors (8 feet max on fire rated openings). We do no...:
How tall of a door can a standard 98/9947 fit?
Resolution:
A standard device mounted at standard templating location will fit up to a 8'4" tall door. Extension rods for non fire rated devices over 10' are available and can be found in&nbs...:
Is there a part number for extension rods for 1690/1990 devices?
Resolution:
From 9' to 10' use part # 4270100197 extension rod kit. :
What are the standard door and frame clearances?
Resolution:
To determine Actual Door Size, the following values are subtracted from nominal door size (frame opening/order size) Actual Door Size: The largest measured width by height of the door leaf as m...:
Can the XX-V, 19-V, 24-V or 25-V extension rod be used on the bottom rod?
Resolution:
The extension rod could be used either on the top or bottom rods.:
What are the part numbers for the new Falcon T latches?
Resolution:
Falcon T Lock Latches No Longer Offered With The T Lock Effective mid June 2013 Old Part Number New Part Number &nb...:
Does the backset extension link work with a 2 3/8" latch or a 2 3/4" latch?
Resolution:
A and AL product: Must use the 2 3/8" backset with the 41-005 extension link D Knob and ND product: Must use the 2 3/4" backset with the 43-005 extension link:
Are the AL locks available with a 5" backset?
Resolution:
This is available, specify 41-005 for an extension link that is used with a 2 3/8" latch to effectively make a 5" backset.:
Is an extension rod needed on 9927 for 7'1" door?
Resolution:
The 9927 installed on a 7'1" door requires a 12" extension rod:
Does Schlage or Falcon offer a backset greater than 5"?
Resolution:
Only the Schlage D-knob and ND products are available with an extra long backset. The part number for backsets over 5"-42" is XC03-069, this part will ship as an extension link to b...:
What parts do I need to convert my AL lock to fit a 2" thick door?
Resolution:
Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...:
How do I wire an EL device to normally hold open the latch and release it during a fire alarm?
Resolution:
Use a normally closed fire alarm as the input to the power supply option board (PS873-2 or PS914-2RS), this will hold the latch retracted. During a fire alarm, the contact will open, dropping...: