Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
mortise lock lever return spring positioning
”
RELATED FAQS
Question
Answer
Does Schlage make a mortise lock that the lever on either side retracts the latch and a key on either side retracts the deadbolt?
Resolution:
The L9466 Store/Utility Room lock can provide this functionality. Operation: Latchbolt retracted by knob/lever either side. Deadbolt thrown or retracted by key from either side. When the deadbolt ...:
Does Falcon have a breakaway lever trim feature on mortise locks?
Resolution:
The MA lock does not have Vandlgard or a breakaway trim feature, however, the lever spindle on the MA lock will shear if too much force is applied in order to prevent internal lock damage and resis...:
What is the part number for the inside lever on an L9000 lock?
Resolution:
The part number is the 09-402, specify the design and finish.:
How do I change the function of the Von Duprin 7500 mortise lock from Lever ( classroom ) to NL ( night latch )?
Resolution:
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory): Turn the NL screw on 7500 mortise lock counter clo...:
Why does my lever sag on an L9000?
Resolution:
Levers may sag due to an incorrectly installed springcage or an incorrect springcage.Mortise locks with a fixed (rigid) lever such as an L9080 will use a spacer on the rigid lever (outside) and a s...:
What is the part number for the lever return spring for the old M series mortise lock?
Resolution:
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series. Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...:
What is the part number for the lever return spring for the MA lock?
Resolution:
Lever assemblies part numbers are found in the Pricebook. Note they are handed.:
Are parts still available for the old Falcon M locks?
Resolution:
Related solution: What is the part number for the lever return spring for the old M series mortise lock?:
What is the part number for the lever return spring for an old 182LE trim?
Resolution:
These parts are no longer available. For reference the spring part number is 4841 and the clip part number is 4326.:
What is the part number for the springcage for an L9000 lock?
Resolution:
The springcage part number is L283-040.:
Can you order the Schlage L series mortise lock with knob on one side and lever on the other?
Resolution:
Includes the SL1 lever on one side and the SK1 knob trim on the other side.:
Why does my AD or CO series lock unlock when the lever is raised?
Resolution:
Installers have reported that their AD-CO Series cylindrical or mortise locks will unlock whenever the outside lever is lifted. This will occur if the outside spindle (square post) is install...:
What ligature resistant trim is available on the ND or L9000?
Resolution:
High Risk Areas*Patient bedroomIn-suite bathroomIn-suite closetTime-out roomPatient difficult to manage; or risk of solitary and/or unsupervised areas.Medium risk areas*Living roomDining roomGroup ...:
Are the ND, NDe, AD and CO levers the same?
Resolution:
Between January 30, 2017 June of 2019, the AD and CO cylindrical lock levers were incompatible because of the ND / NDe lever and spring cage design change in January of 2017.Prior to January ...:
I get three green blinks of the Schlage key and it says motor stall on my SUS/HHD during diagnostics?
Resolution:
Just align the triangles per the installation instructions to allow full motor movement. - This will eliminate the SUS motor STALL report. - This will eliminate the three ...:
Why is the Von Duprin 55 or 88 series crossbar sagging?
Resolution:
There are a number of reasons the Von Duprin 55 or 88 series cross bar may not operate properly:The hinge case spring lifts both lever arms and the crossbar. To check spring, push down on...:
What is the part number for a L mortise lock spindle?
Resolution:
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1. Spindles and Springs Part Number Description L283-060 Spindle and spring, 1...:
What is the ME9453?
Resolution:
At one time we offered a 9453 function in several different lever, knob and grip handleset designs. A wide variety of trim offerings were available. The mortise lockcase was a smaller version of th...:
How to convert a ND series lock cylinder format from PD to BD?
Resolution:
On ND locks manufactured prior to January 30, 2017, the lever, spring cage and tailpiece needed to be replaced with the SFIC lever, SFIC spring cage and the SFIC driver . N123-056 - Outside sp...:
Why can't I get my JD YA6 cylinder to install into an AD-Series lock?
Resolution:
The JD YA6 tailpiece is intentionally designed such that the tailpiece cannot be installed at the same time as the cylinder. Interchangeable cylinders assume that the lever and taipiece is i...:
What is the square block that holds the L lock levers onto the door?
Resolution:
The square block is probably the springcage assembly, L283-040. This component has an internal spring to keep the lever in the horizontal position.: