Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
mininum stile for Schlage Locks
”
RELATED FAQS
Question
Answer
What is the part number for T lock tailpiece used with a conventional cylinder?
Resolution:
Refer to Table 1 for a list of T lock tailpieces for conventional cylinders. Table 2 shows IC tailpieces. Table 1: T lock conventional tailpieces Table 2: T lock IC tailpieces:
What backsets are available on Schlage and Falcon locks?
Resolution:
SCHLAGE locks are available with the following backsets: Lock Series Lock Type  ...:
What size is the Schlage H escutcheon?
Resolution:
Schlage H-Series Escutcheons Part Number Description Dimension 07-057 Inside escutcheon and turn 6.92" x 2.75" 07-035 Inside escutcheon, dummy - H170 6.92" x 2...:
What is the minimum stile an MA lock can fit?
Resolution:
Depending on the door construction the minimum stile may differ but a safe dimension would be 4-3/4". CUSTOMER must check door construction. The pocket depth requirements of the case is 4 1/2".:
How many AD300 locks can be connected to a PIB300?
Resolution:
The PIB300 may connect up to two Schlage AD-300 locks or up to two legacy VIP locks (PIB300 in legacy mode) For detailed information see the attached user guide.:
How do I remove the lever on an M lock?
Resolution:
To remove the M lock trim follow the steps below in reverse. The M lock spanner wrench is 021415. Although this wrench is no longer available from&n...:
Does Schlage offer a rabbetted latch and strike kit?
Resolution:
Schlage does offer rabbetted latch and strike kit: Part number, 39-030, for cylindrical locks and deadbolts. Part number, 10-075, for the L9000 mortise locks. Monarch does not offer rabbette...:
What are the part numbers for the inside and outside knobs for the L series?
Resolution:
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish:
What is the part number for the springcage for an L9000 lock?
Resolution:
The springcage part number is L283-040.:
What is the part number for a Schlage cam to operate a Corbin lock?
Resolution:
Schlage offers several Corbin Russwin competitor cams. The left most column in the image below describes what Corbin function the cam is used on and the additional columns show Modular,...:
What is the part number for the Schlage cylinder to work in a Falcon T lock?
Resolution:
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks. Table 1 below contains part number for T series locks. Table 1 - Falcon retrofit cylinders :
What is the part number for the Schlage small format rim cylinder tailpiece?
Resolution:
B502-899 is the tailpiece for both the SFIC and standard rim cylinders.:
What are the minimum stile and rail dimensions for the L-Series door FG, FG2 & FG3?
Resolution:
The minimum stile and rail dimensions are to exposed glass are: Stiles = 6 13/16" Top Rails = 6 3/4" Center Rails = 7 1/2" Bottom Rail = 10 3/4" For high traffic and high abuse locations th...:
What is the part number for the Schlage thumbturn rim cylinder?
Resolution:
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...:
Where can I find hurricane ratings for Schlage and Falcon?
Resolution:
There are several Schlage and/or Falcon locks that have been tested and approved for this application. For Commercial use the locks have been tested and approved as ...:
Available kits to convert classroom mortise locks to classroom security locks.
Resolution:
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077. The...:
Does the PD listed with lock model number mean anything?
Resolution:
Schlage and Falcon use the P cylinder suffix to designate conventional key-in-lever (KIL) 6 pin cylinder. The D means that the lock will have a deadlatch.:
What is the part number for a L mortise lock spindle?
Resolution:
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1. Spindles and Springs Part Number Description L283-060 Spindle and spring, 1...:
Which conventional cylinder cam is used with an Adams Rite MS series lock?
Resolution:
L583-446; Schlage Adams Rite MS modular cam used on 1 1/8", 1 3/8" and 1 5/8" cylinders L583-447; Schlage Adams Rite MS modular cam used on 1 1/4", 1 1/2" and 1 3/4" cylinders B502-944; Sch...:
What is the recommended Stile Size for AD and CO?
Resolution:
The minimum recommended Stile measurement is 5” to allow proper mounting of the AD and CO series locks.:
What is the part number for a control pin for a 23-030?
Resolution:
There are two parts that can be referred to as control pins for a 23-030 (FSIC core).C603-967 is the lower control pin that sits in the seventh hole of the FSIC plug. (part B in exploded view) ...: