Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
minimum Stile sizes
”
RELATED FAQS
Question
Answer
What is the minimum stile for Schlage locks?
Resolution:
The minimum stile for each lock will depend on the backset and the rose diameter/escutcheon width. See the Schlage Minimum Stile Requirements for the minimum stile for eac...:
What is the minimum stile an MA lock can fit?
Resolution:
Depending on the door construction the minimum stile may differ but a safe dimension would be 4-3/4". CUSTOMER must check door construction. The pocket depth requirements of the case is 4 1/2".:
How far down can an exit device be cut down in the field?
Resolution:
For most exit devices, please refer to the specific device series catalog for minimum door opening width the device can be cut down to fit. Be aware that some device options, frame...:
What is the recommended Stile Size for AD and CO?
Resolution:
The minimum recommended Stile measurement is 5” to allow proper mounting of the AD and CO series locks.:
What is the minimum dimension from the edge of the door to a glass light cutout?
Resolution:
Minimum dimensions to cutouts for glass lights: Vertical edge of door to edge of cutout = 5 29/32" Top of door to top of cutout = 6" Bottom of door to bottom of cutout = 10" Reinforcing chann...:
What are the minimum stile and rail dimensions for the L-Series door FG, FG2 & FG3?
Resolution:
The minimum stile and rail dimensions are to exposed glass are: Stiles = 6 13/16" Top Rails = 6 3/4" Center Rails = 7 1/2" Bottom Rail = 10 3/4" For high traffic and high abuse locations th...:
What is the minimum stile for the 98/99 rim device?
Resolution:
Minimum stile depends on several factors. The information will be on the specific template for your door and hardware.Start by opening the templates page.Click here -->: 98/99 T...:
What wire gauge is recommended for LCN hardwired actuators?
Resolution:
LCN recommends an 18 AWG (minimum) wire size (gauge) to the 8310 Series hardwired actuators.:
What is the minimum rose dimension that can be used with a Steelcraft 61L lock preparation?
Resolution:
The minimum rose that can be used on the 61L (ANSI/BHMA A156.115.18) preparation is 3 7/16".Steelcraft's 61L lock prep (often referred to as the "Squashed Turtle lock prep") is designed for Bored L...:
Can a door have an InPact device and glass lights?
Resolution:
Glass lights available: Standard Glass Lights - The N4, N5 & V lite can be used at standard locations with out any modification. Glass Light Options - Other glass lights are available but ...:
What is the mounting difference between a 2010 closer and a 2030 closer?
Resolution:
The 2010 and 2030 closer are not the same. The 2010 Series closer uses the (larger) 4010 cylinder which requires a 4" minimum frame tube to mount in. The 2030 uses the (narrow) "Pacer" cylinder...:
What is the maximum size for a Dutch Door?
Resolution:
Maximum Dutch Door sizes are:Non Labeled = 4'0" wide X 8'0" HighLabeled = 4'0" wide X 7'2" HighSpecial sized Dutch Doors are available:Special size top and/or bottom leaves are available.When order...:
What is the part number for a FSIC?
Resolution:
DESCRIPTION PART NUMBER Conventional Core 23-030 Conventional Core less logo 23-031 Primus Core 20-740 Primus XP Core 20-740-XP Primus Core less logo 20-741 ...:
What is the maximum size of a welded elevation frame?
Resolution:
The following size limitations per frame unit, are in enforced for welded elevation frames shipped from the factory. These limitations are in place due to the physical size of shipping tr...:
MEETING STILE
Resolution:
Lock Edge, Strike Edge:
HINGE STILE
Resolution:
Hinge Rail:
MA lock case dimensions.
Resolution:
See below for commonly requested dimensions on the MA lock. Dimensions not found in other literature have a square around them. CL refers to "Centerline". :
Can you get a 33/35A Rim device fire rated?
Resolution:
Yes. A fire rating was approved in 2016.Please see the 33A/35A catalog here for more information:http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/Catalog/Von_Duprin_33A.35A_Se...:
Can you order 8827L-F less bottom rods?
Resolution:
Von Duprin will not supply the 8827-F less the bottom rod because the device has never been UL tested less bottom rod.: