Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
maximum door weight for overhead stops
”
RELATED FAQS
Question
Answer
Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?
Resolution:
ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:
What special template (ST) is used with a 4110 closer and GJ90 series?
Resolution:
ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:
What is a 62A shoe used for?
Resolution:
The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc.:
What is maximum width, height and weight for IVES butt hinges?
Resolution:
Butt hinges can be used on doors up to 4' wide and 200 pounds. There is no maximum door height. However, an additional hinge must be installed every 30" when exceeding a 7' d...:
What is the maximum door weight recommended for LCN closers?
Resolution:
The maximum recommended door weight for LCN manual closers is 225 lbs.:
How do I get a special template for a Glynn Johnson overhead stop or holder with special door considerations?
Resolution:
To determine if a Glynn Johnson overhead device will fit on a door with special considerations, we will need the following details: What overhead stop/holder series and size are you want...:
What mounting group do I use if my hinge type is not listed in the Glynn Johnson overhead door holder and stop instructions?
Resolution:
To determine if a Glynn Johnson overhead device will fit on a door with special considerations, we will need the following details: What overhead stop/holder series and size are you w...:
Can a 4040 regular mount installed on the pull side and a Glynn Johnson 90 be mounted together?
Resolution:
The LCN 4041/4040XP and the Glynn Johnson 90 series can be mounted in conjunction with each other without a special template. The 4040 door closer is on the pull side of the door and the GJ 90 is ...:
Can a 4110 EDA and a Glynn Johnson 100 be used together?
Resolution:
A special template is not needed, the closer drops down far enough on the door where it does not conflict with the GJ100 series concealed overhead stop. :
Can I mount an LCN Cush closer with an GJ overhead stop?
Resolution:
It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:
What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?
Resolution:
The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:
What is the max rating available on an full glass (FG) door?
Resolution:
A UL 20 minute fire rating is the maximum fire rating for a Full Glass (FG) door design. A14-Series door construction: Max fire rating is 20 minute. UL label only FG must use Over-Lapping Stee...:
Olivari door stop dimensions.
Resolution:
Dimensions shown are in millimeters. Cubo & Cubo Mag have the same dimensions. Victor & Victor Mag have the same dimesions :
What is the function of an SE version of Glynn-Johnson overhead stop series 90, 100, 410, or 450?
Resolution:
The SE is a special Stop Only function available with certain overhead stops (90, 100, 410, 450 series). The SE stop should only be used with single-point hold-open electronic closers such ...:
For a Glynn Johnson Stop: Is 110 degrees the largest degree of opening ?
Resolution:
Yes.. However, the spring will compress (if using a spring model and have not templated for dead stop) and the door will get an additional 5-7 degrees. :
Will the AL lock fit a 2" thick door standard?
Resolution:
The AL series lock fits up to 1 7/8” door thickness out of box.:
What is the standard Steelcraft door thickness?
Resolution:
1 3/4" is the standard door thickness. Steelcraft only makes a nominal 1 3/4" thick door. A 1 3/8" was made for light duty commercial applications but that product was discontinued in 1999.:
What is the maximum door thickness a Rim cylinder can fit on?
Resolution:
For total thickness measurements larger than 3 inches see the special cylinder offerings in the Schlage Pricebook. Specify the part number and include the total thickness. We do no...:
What is the minimum and maximum door thickness for the AD and CO series locks?
Resolution:
The minimum door thickness that the AD or CO series lock will mount on is 1 3/8". Be advised that this will require additional spacers to be ordered separately to allow the lock to mount...:
How do you adjust a door closer?
Resolution:
How to: What are the steps to adjust a door closer? Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All cl...:
What is clear opening width?
Resolution:
Clear Opening Width for swinging doors is measured (with the door open 90 degree) from the face of door to stop soffit on strike jamb. &nbs...:
Do we have a maximum door width or height for using pivots?
Resolution:
The maximum door width that pivots have been tested is a 4' wide door. Any door greater than 4' would shorten the life of the pivots. There is no maximum door height, for offset pivots the ru...: