Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ loose exterior lever on L-Series ”

RELATED FAQS

Resolution: For ND locks shipping prior to January 30, 2017, the addition of the soft durometer spacer (SDS) on August 15, 2012 did affect the installation of the lever. Ultimately, removing th...:

Is the MA lock available with the RX feature?

Resolution: The MA RX features a single switch within the chassis that will monitor both the inside and outside knob/lever. The switch is only available as Normally Open (NO).:

How does the 98-2 or 99-2 double cylinder function affect the outside lever trim?

Resolution: Double cylinder (-2 or -2SI) features an inside key cylinder which locks or unlocks the outside trim and an outside key cylinder which retracts the latch bolt only (Night latch function). Thi...:

Why doesn't full rotation of the AD or CO Series Exit Trim (993) outside lever fully retract the Von Duprin 98/99 Exit Device latch?

Resolution: - AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device. Be sure this screw is installed- Exit hardware and strike must be properly mounted ...:

Why does my lever sag on an L9000?

Resolution: Levers may sag due to an incorrectly installed springcage or an incorrect springcage.Mortise locks with a fixed (rigid) lever such as an L9080 will use a spacer on the rigid lever (outside) and a s...:

What is the L Series inside lever mounting plate part number?

Resolution: The inside lever mounting plate part number is L283-031.:

Can you order the Schlage L series mortise lock with knob on one side and lever on the other?

Resolution: Includes the SL1 lever on one side and the SK1 knob trim on the other side.:

AD-993 - Cylinder loose in lever - Spacer missing

Resolution: In the early cylindrical version of the AD-Series 993 locks, a spacer may be required for proper cylinder functionality. Effected cylinder types are PD / LD / RD / JDIf a customer is ...:

Why does my 7500 retract the latch bolt but not re-lock the trim?

Resolution: Tips for changing the function: The NL Drive screw will not be visible when lock body is set to Classroom function There is locktite on the screw that makes it seem like its turned down enou...:

What are the part numbers for the inside and outside knobs for the L series?

Resolution: Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish:

Outside lever on the T and RU 571's won't unlock after egress.

Resolution: Replace the lock chassis as necessary for any T locks exhibiting this issue. RU locks need to be replaced entirely. :

What other locks can the blue lever removal tool 24002693 be used with?

Resolution: On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:

What grade of stainless steel do we use in the levers on L9000 locks?

Resolution: Schlage offers 629 and 630 stainless finishes on levers for the L-Series only. These levers are made of 303 or 304 grade stainless steel.:

Why does the ND40 stay locked after egress?

Resolution: There is potential for ND40/ND44's manufactured around March 2011 to remain locked after egress, or after the latch is depressed. There was an issue with the keycam that created a bind when l...:

What locks are always locked on the outside?

Resolution: The storeroom lock function is described as follows: Latch bolt operated by key from outside or by operating inside lever. Outside lever is always inoperative. The following are storeroom functi...:

What is the part number for the outside trim assembly on L9000 mortise locks?

Resolution: Outside Knob/Lever and Rose/Escutcheon Assemblies Part Number Description A Rose with Knob/Lever 09-506 Designs: 01 02 03 05 06 07 12 17 18 OME 41 42 09-655 Des...: