Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
l series thumbturn timing
”
RELATED FAQS
Question
Answer
Is the Schlage Latitude and Longitude lever available in a stainless steel finish?
Resolution:
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.:
Available kits to convert classroom mortise locks to classroom security locks.
Resolution:
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077. The...:
What is the part number for the L series handing screw?
Resolution:
Screw part number is L583-485. Screw type: 8-32 UC-2A W/#6 Flat truss head Phillips recess, header point.:
What is the part number for a L mortise lock spindle?
Resolution:
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1. Spindles and Springs Part Number Description L283-060 Spindle and spring, 1...:
What is the L Series inside lever mounting plate part number?
Resolution:
The inside lever mounting plate part number is L283-031.:
What are the part numbers for the inside and outside knobs for the L series?
Resolution:
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish:
How long does it take to install a L Series mortise lock?
Resolution:
Typical installation by an experienced Schlage L lock installer on a door correctly prepped for the Schlage L-Series function could take 10 to 20 minutes. Many outside variables can change the amo...:
Can doors be prepared for raceways in the factory?
Resolution:
Raceway availability: Optional factory installed raceways are available in doors but are not available in frames. Preparation Info: Steelcraft installs a flexible 3/4" ID steel...:
Factory installed louvers?
Resolution:
Stamped louvers are no longer available from Steelcraft in any door series. Steelcraft discontinued this offering in 2008. Steelcraft will only provide a cutout only in doors for louvers.:
What is the max rating available on an full glass (FG) door?
Resolution:
A UL 20 minute fire rating is the maximum fire rating for a Full Glass (FG) door design. A14-Series door construction: Max fire rating is 20 minute. UL label only FG must use Over-Lapping Stee...:
Can you order the Schlage L series mortise lock with knob on one side and lever on the other?
Resolution:
Includes the SL1 lever on one side and the SK1 knob trim on the other side.:
Is there a round corner armor front for the L series mortise lock?
Resolution:
The L series armor fronts are only available with square corners. :
What is the wire gauge on the motor driven L9000 mortise locks?
Resolution:
Supply wires - 24AWGRX wires - 20AWGLX wires - 20 AWG:
What cylinder length do you use for escutcheon trim for the L series mortise lock?
Resolution:
Typically for a 1-3/4" door you would use a 1-1/4" cylinder. Use the Table in the Pricebook for a reference:Note: The 30-001 used with Rose trim on double cylinder applications requires a Blo...:
How to build an L-Series chassis.
Resolution:
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...:
What type of switch is used for the RX and latch monitoring options for the ND and L locks?
Resolution:
The ND-Series RX, the L-Series RX and latch monitoring switches are Form C - Single Pole Double Throw (also known as SPDT).: