Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ hold open arm going back into hold open at latch ”

RELATED FAQS

Resolution: The 1460 Regular Arm part numbers are: Regular Arm -- 1460-3077 or 1460-3077L for long arm (must specify finish). Regular Arm with PA -- 1460-3077PA (must specify finish). Regular Hold Open Ar...:

Where does the hold open switch on the 4630 / 4640 wire into on the 1-24 single terminal strip?

Resolution: The 4600 hold open switch (for the new 1-24 single terminal strip I/O board) wires into terminals 2 and 6 or 4 and 6.:

How do you order a 4110 hold open spring cush arm only?

Resolution: The 4110 hold open spring Cush (Spring H Cush) arm part number is 4110-3049SCNS.:

Is there a left hand hold open clip (block) for a 3130 series closer?

Resolution: As of Feb. 8th, 2016- LCN launched a new HO feature (block) for all track closers, which is not handed. Part # for the Hold Open clip (block) is 3130-3054 and it also requires the...:

How to adjust a 4010 hold open arm?

Resolution: The correct method (process) for setting the hold open is: The 4010 hold open arms are handed, verify correct hand arm. (R or L stamped on main arm) Loosen the hold open nut. Opened the door ...:

Why would a 4600 not open a full 90 degrees?

Resolution: A 4600 (4630/4640) not opening to a full 90 degrees could be caused by a couple things: The Opening Force could be set too low. Try increasing the opening force adjustment on the contr...:

How do I set the hold open on my 4040 closer?

Resolution: The hold open position on a "REG" or "EDA" hold open arm is set with the door to a few degrees shy of the desired hold open point. To properly set, open the door 5° less then the desired hold open...:

What would cause an ME Series closer (2310ME/4310ME/4410ME) to pop back into hold open as it is closing?

Resolution: This condition can be caused by the "closing speed adjustment" being regulated for a fast closing speed. Try adjusting the closing speed to slow down the closing of the door. If that does not corre...:

What do I need to do to make my 4041 Reg/PA a hold open arm?

Resolution: When placing an order for a 4041/4040XP Rw/PA with hold open, it would be ordered as a 4041 /4040XP Hw/PA. For an existing Rw/PA requiring the addition of a hold open function, a hold open arm woul...:

What degrees of opening can a 4110 EDA be templated for?

Resolution: The 4110 EDA/HEDA can be templated for 100°, 140°, and 180° hold open. The hold open adjustment can be set to hold the door at any position (degree) up to the maximum door opening angle. For "Wi...:

Will a 4040SE open and hold at 180°?

Resolution: No, LCN does not have an electronic hold open closer (SE/ME Series) that will provide a solid 180° hold open position. The 3130SE has an adjustable hold open position from 85° to 110° maximum. ...:

Can you replace a regular arm with a hold open with out moving the door closer?

Resolution: Yes, as long as you stay with the like style arm. Example: replace an RW/PA with HW/PA, replace an EDA with HEDA, or replace a CUSH with HCUSH.:

How do I wire an EL device to normally hold open the latch and release it during a fire alarm?

Resolution: Use a normally closed fire alarm as the input to the power supply option board (PS873-2 or PS914-2RS), this will hold the latch retracted. During a fire alarm, the contact will open, dropping...:

When did the 4111 Cush arms become non-handed?

Resolution: This engineering change did affect the templating of the closer. The stop in the shoe is slightly larger than the original handed cush shoe. The new non-handed arm template locates the closer and s...:

Will CX re-arm if door is held open?

Resolution: If a door position switch (DPS) is connected across the green and white wires of the old CX (green and red of new CX) the CX would go into alarm if the door is held open when it attempts to rearm.&...:

What is the part # for the 4040 HCush arm?

Resolution: The part number for the 4041/4040XP HCush arm is 4040XP-3049CNS.:

What power supply is needed for EL devices?

Resolution: You can use a Von Duprin PS914 power supply with any of the following option boards depending on the application. 900-2RS board will power 1 or 2 devices that do not require timing from pow...:

What is the part # for the 4040 regular arm?

Resolution: The 4040 regular and hold open arms are different. You would have to get a different arm to convert from regular arm to a hold open function. 4040-3077 for a regular arm. 4040-3077L for a long ...:

What is the purpose of a Swing Free arm on a 4310ME?

Resolution: The (SF) "Swing Free" arm allows the door to be put into hold open position, but then repositioned (swing free) to any other degree of opening without taking the closer out of the hold open mode....: