handkey with MT reader

RELATED FAQS

Question
Answer
Prom Version Release Date Reader Type Model New Functions or Options Summary 265 2006 F-Series All Improvements to remove the occurrences of random resets on Ha...
Our biometric hand readers have a limitation on how many times you can try an unsuccessful  hand verification. This is similar to secure computer/ system logins that kick you out after a certa...
The following technical note describes in detail the process for upgrading a biometric F-Series HandKey or a biometric F-Series HandPunch main board with a new firmware chip. Note: A firmware upgr...
F-Series (Handkey and HandPunch) firmware upgrade
The following technical note describes in detail the process for upgrading a biometric F-Series HandKey or a biometric F-Series HandPunch F1-style main board with additional RAM.  Please ...
Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1)      One the four (or eight) AA was inserted reversed and the rese...
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels. - These are approximate values/levels which change with measurement meters and measure...
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery Holder New batteries = 6.2 VDC Low battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4...
    AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery Holder New batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/...
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
  CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...
Use a multi-meter in series with the batteries to measure battery current.  Be sure your multi-meter can accurately measure very low current, in the micro-amp range. See the attached Technical Not...
It's essentially the same as the usual MT reader except that it has an embedded HID iclass reader to read the secure part of an iclass card. So yes it will.
Multi-technology reader capable of reading 125kHz (Prox) and 13.58MHz (smart) credentials.
Yes, press the * (asterisk) key 10 times on the reader.  The serial number will be displayed.  A second way of locating the serial number on the reader is to visually check...
A biometric F-Series hand reader usually comes with standard user memory.  When a user is added that exceeds that user memory size, there is no room left to store that user and that user template c...
The following technical note describes in detail the installation process for upgrading a biometric F-Series HandKey or a biometric F-Series HandPunch with a modem communications mod...
HandNet Lite is a no-cost application that can be found on the Access Control Support Disk.  The disk is included with every HandKey.  The application can also be obtained through an FTP ...
When you see an Error 64 on a HandKey or a HandPunch, it may mean that the lithium battery is low or there is a disconnect with main board.  The first step is to replace the lit...
 A F-Series HandKey II can be operated as a stand-alone access control station, as a network master enrollment station, or as a networked access control station which receives and processes co...