find proximity card number hotstamp

RELATED FAQS

Question
Answer
A generic name for contactless integrated circuit devices used for security access or payment systems. The industry generally refers to cards that operate at 125kHZ as proximity cards. These cards ...
See attachment for details: Proximity readers support
All Schlage/XceedID wiegand proximity readers currently understand: -ASK (Amplitude Shift Key) - Used in GE/CASI -FSK (Frequency Shift Key) - Used in HID Prox, AWID, and Lenel The third proximit...
ISOX card technology is no longer supported - contact XceedID sales
The bit structure of a particular card. The average card format includes the card number, facility code, and parity bits. The two types of card formats supported by Cisco Physical Access Manager ar...
The radio frequency identification wavelength used by various manufacturers of proximity cards. This frequency is utilized by the reader to energize the credential in order to read the information ...
Type of smart card format whose serial number is readable by AD Series proximity and multi-technology readers.
Type of smart card format whose serial number and secured sector are readable by AD Series proximity and multi-technology readers.
Type of smart card format whose serial number and secured sector are readable by AD Series proximity and multi-technology readers.
Type of smart card format whose serial number and secured sector are readable by AD Series proximity and multi-technology readers.
A device used to validate electronic credentials, such as a magnetic stripe readers, proximity card readers, smart card readers, etc.
  Part Number Level  Classic Primus 40-061 1  40-065 1 Plus  40-062 2  Classic Primus XP 40-061-XP 1 40-065-XP 1 Plus  40-062-XP 2 Everest Primus 40-06...
         
  The Legacy wall mounted readers are replaced as shown in the table below:  The MTMS15 and MTMSK15 did not have any prior models that it replaced.
The sequence card part number is 3426 and plugs in the "S" slot of a control boxes right next to the 10 pin terminal strip. The 7902/7902ES or 7982/7982ES can be converted to a 7902S/7902SES or 79...
The part number for the solenoid air valve in the 7900 Series control boxes are: 7901/ES7901 - part# 941 - marked A 7902(S)/ES7902(S) - part# 942 - (2 valves) marked A and B 7949/ES7949 - part...
There are two new credentials available which allows a facility currently using iButtons credentials to transition to proximity credentials. Since the new AD and CO series units no longer supp...
Product Ordered after 7/10/2012 - Product identified by label on QEL motor You no longer need to use the 900-2Q option board (no longer available) with the PS900 power supplies to ...
Product Ordered before 7/10/2012 - Product identified by no label on QEL motor. You must use the 900-2Q option board with the PS900 power supplies to operate the QEL devices.  The attached ta...
If an access control system is not available to test the card output on a hand reader, this card emulation test can be done to verify the card format is correct.  These steps will guide you in...
“Cache Mode” is an AD-Series feature which, accumulates and stores valid credentials that have recently been granted access by the Access Panel or head-in system. This recently granted access histo...
The number of bits selected for "Card Bit Format" on an AD400 or AD300 must be equal too or larger than the bits on the cards in use. Setting this number correctly enables the cache mode collectio...
The AD300 and AD400 devices do not store audits during cache mode.  Audit "Date and Time" information and the saving of audit information is an Access Control Panel function, and during cache mode ...
An AD400 granting credentials access in “cache mode” will blink the Schlage with the normal green LED, followed by a brief red Schlage LED flash, indicating no RF communication and access was grant...
ALWAYS put the PIM400 in LINK mode first. On a PIM400-TD2 press the LINK1 Button for door one, and LINK2 button for door 2. With a PIM400-485 you must use the SUS/HHD to select which door to LINK.  
1. To put the AD400 in LINK mode, hold down the RTE (Lever or crash bar see below) and press the # key on the key board, or present a card to the reader.            Why press the # key? Because t...
2. AD400 requires a Request To Exit (RTX) signal to link - see the user guide instructions for the linking process.  For an AD400 to enter link mode, it must see the RTX (Request To Exit) switc...
   3. Check the AA battery level, if the AA batteries are below 4.7 volts the AD400 can fail to LINK.             Install fresh batteries, with a level of 6.0 volts or better.  
4. PIM400/AD400 COM400 plug could be damaged! The small pins in the Main PCB board connection for the RF COMM board can get bent during installation of the RF COM400 board. If the PINs are bent a...